I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hello,
I need to send logged sensor data in external 4MB flash to a phone via BLE.
I am using a nRF52840 based module on a custom PCB. I am using SDK v14.2.
I am using...
Hello,
Is it possible to get access to the information contained on the SIB (System Information Block) in the nrf9160? if yes, is it through the nRF Connect v3.3.0?
Thanks...
I want to get the 128 characteristic UUID of the peer device during the connection phase. Now I use SDK is 15.3, the softdevice is 6.1, and only 16-bit UUIDs are obtained...
I have the NRF52 DK, I run make flash in the UART example, everything works. I'm able to run the loopback test.
I navigate to the serial port example, make flash, nothing...
Hi Everyone,
I would like to understand how the multi peripheral application works in this given scenario:
Scenario:
Considering one peripheral (P) is connected to 4...
Hello,
I have been working with NRF 52840 DK and finally able to make the advertising work on PHY CODED but I was required to use extended packets.
My question is
Is...
Hi i am using sdk15.3 secure boot-loader example. i had change backend to cc310. without optimization i am able to upgrade code but when i am using optimization level 0 it...
Hi,
I am working on an USB CDC program with nrf52840-mdk-usb-dongle. The PC needs to use a terminal emulator like putty to connect to the dongle. Now I send and recieve...
I use Zigbee CLI example on nRF52840. (examples\zigbee\experimental\cli\cli_agent_router)
It use UART as 115200 bps with CTS/RTS (hardware flow control).
I want to change...
Our product uses non-connectable/undirected advertising, where advertisement packets are sent every 1 minute for 500ms time. For that we are using FreeRTOS timers to start...
1: Is there any information that can be systematically introduced to the production test of Bluetooth products? 2: What parameters do I need to test for mass production of...
Apparently， Config AppKey Update message can be transmitted in the key refresh procedure. However, one point let me very confused, I looked into the Mesh Spec v1.0.1 (page...
Hello. Is it possible for a central device to retrieve the BDADDR( 6 byte array data ) of a past peripheral device by using the peer manager? ("past peripheral device" refers...
Does anyone know how the raw data message is structured to enable GATT Proxy? Here is a screenshot from the app. I know one byte is used to indicate whether to enable or disable...
Hi,
actually I developed a system based on an nRF24AP2 able to read data coming from different HRM ANT+ sensors and transmit them via WiFi using ESP8266 that is acting as...
