Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hello all!
How can I get the current count of a timer without stopping it?
Right now I'm doing like this:
_timer_base->TASKS_CAPTURE[channel] = 1; uint32_t counter...
Hi,
I am no programmer, but I wanted to try the Wake-on-NFC example on the 52840 dongle (I soldered an NFC flex on pins P0.09 and P0.10). I have downloaded SES and nRF SDK...
I want to connect heart rate sensor and bike power sensor together. I config channel 0 for heart rate sensor,and channel 1 for bike power sensor. Ant work well when both sensors...
I've just tried to compile and run the stock lpcomp example on two different computers, targetting an off-the-shelf 52840 dev board. It compiles, and starts fine, but doesn...
Hello,
I am creating an application that counts the number of times the button is pressed (Every high to low transition).
I am using GPIOTE to sense the high-to-low events...
Hello,
I am considering redistributing the SDK source code. I also saw the following, but hasn't it changed?
devzone.nordicsemi.com/.../32969
【SDK：15.3】
Hi,
How can I understand what all Errata's are applicable to softdevice and are taken care of?
For my application I am aware of the modules/peripherals being used and...
Hi,
I noticed there is no SWO support mentioned in Product Specification 1.1 for nRF9160. But since the architecture seems similar to the nRF52/nRF53 that have SWO under...
I have been interfacing with the Macronix external flash via the nfrx_qspi library for logging. While I am able to use nrfx_qspi_read() to obtain my log data, I am also able...
PM_MCUBOOT_STORAGE_ADDRESS and PM_MCUBOOT_STORAGE_ID seem to be no longer defined as of SDK1.2. As per the discussion here , I tried using DT_FLASH_AREA_STORAGE_OFFSET which...
Using nRF52811, Segger SES, and SDK 16.0, I have some times that seem to be off by ~2X.
I'm timing by setting a gpio before and after the event and capturing with a scope...
Hi
Referring to
https://devzone.nordicsemi.com/f/nordic-q-a/58652/additional-questions-to-nrf52832-errata-220-clearification/238659#238659
From the above post, the...
I am new to the nRF9160dk board. I have been able to compile and run some of the sample programs. I am now looking to have a simple program to talk to external uarts 0 and...
I need my sara sara-r410m-02b ublox module to connect to the cellular network using at commands. For this reason I require to send the commands by means of programming lines...
