I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
Greetings!
I am using nRF52832 with SDK 16.0.0 and mesh sdk 4.0.0.
Application: light switch client with LPN features added
In one of application, I have to use...
i already done the nrf52840 dongle that already work as beacon when i have tried in nrf beacon apps. i want the same application but now it is transmitting to server/website...
Hi,
I have a low level mcu (128 kbyte flash) connected via UART to the nRF52840.
My current flash usage (text output arm_gcc) is about 256 kbyte + the softdevice.
Since...
I am somewhat of a beginner - I have successfully built and programmed a "Hello World" example on the nRF5340. However I am having trouble building some of the Bluetooth samples...
So I am using the Mesh SDK in version 4.0.0 and 2 nrf52DK boards with some custom software running on the boards, but derived from the light switch examples. The boards work...
We have some prototype boards that work fine when programmed via the debug out on the nRF52 dev kit, but have problems when programmed with this JLink . Programming with both...
Hi Team,
We are using the NRF52832 Board for our development purpose.We need the last RESET condition reason/source and need to store as log in memory for further debugging...
Hello,
I am looking for some tips to speed up a DFU transfer.
I have 2 BLE, I implemented a DFU master in the first one using SDK11.
Transfer duration is about 3mn30s...
Hi, I am trying to do firmware upgrade of nRF91 over BLE using nRF52 on the nRF91-DK or Thingy91 board. They both have nRF91 and nRF52840 chips on them which are connected...
I am currently working on a Heart rate sensor(max30102). I have connected the sensor to my nrf52 DK as follows: GND -> GND VDD -> VIN SCL -> P0.27 SDA -> P0.26 INT -> P0.17...
Hi everyone,
I have lately had some problems with my application which has different characteristics enabled, such as nus, battery service, dfu etc...
The problem I am...
Hi team,
I have 2 Thingy:91s, 1 is maybe new, not sure if I have used it before and 2 has been used before and reprogrammed over SWD many times before.
I wanted to test...
Hello,
I am working on my nordic board to make an https request to download some data that is about 4200 bytes. It is failing because of the BSD_IP_MAX_MESSAGE_SIZE=4096...