I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
I'm trying to use th nRF52832 as a slave SPI device but in the examples "spis" I see the firmware uses DMA.
Can I use it without DMA?
Also, what is the difference...
Hi ,
I need to generate a count data to third party library.
So I create a timer1 ,it can work well.
But I set time_us equal to 1 ,the "timer_led_event_handler" don...
I am interfacing external RTC PCF8563 to nrf52840. Also I will be using low power sleep mode. Will it be possible to wake up nrf using 1hr alarm interrupt of rtc?
Hi ,
I am working on the project based on nrf9160.
Please verify it-
1. I want to print the current clock source of the board as board is initially work on LFCLK....
Hi!
I am feeling a bit stupid, since I know that I must have made a config error somewhere. I just don't know where. I am developing a BLE HID device using SDK 16.0 and...
Hello,
I have trouble with interrupt.
I use pin 16 to trigger interrupt signals from a sx1261 module.
It has worked well on example code with SDK 14, but for my projet...
SDK Version: 15.1 IDE: Keil Softdevice: S132 v6 Example: Blinky peripheral example slightly modified Q1. Does the Softdevice use RTC0? Q2. Does the App Timer use RTC1? If...
Hello everyone,
I am using the pc-be-driver-py library to start a scanning with IRK and I view the advertising events that I get. My peripheral is configured to do 1 advertising...
When i compily the SDK16.0.0 example project: iot_secure_dfu_bootloader_secure_dfu_s132_pca10040 i get error after Linker, saying .rodata and .data are too large for the flash...
Hi, As per our requirement, we have integrated GCP on thingy91 (PCA20035) and able to send and receive MQTT messages without any issues. But as part of FOTA implementation...
Hi,
I'm using the light switch example and lpn example from the Mesh SDK 4.1.0.
I have one Board as the light switch client (gateway), one as the light switch server ...
Hello,
I have included nrf_pwr_mgmt.h to the gpiote_pca10040 SES example to able to run "nrf_pwr_mgmt_init();" function.
I have added nrf_pwr_mgmt.c file under the nRF_Libraries...
Hi
I'm using nRF52832 and trying to make programming patterns via SWD myself, and want to make programming time short.
I have a question about flash programmng time via...
