Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi,
I using custom nrf52840 board .I have loaded the Bluetooth program in to the custom board using swdio/swclk/vtg/gnddetect these lines.There is no problem in Bluetooth...
I'm attempting to get MMD set up in an IAR project following this tutorial: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/monitor-mode-debugging---revolutionize...
Dear sir, We are using BL654PA from Laird technologies. We want to check RSSI at 2402MHz, 2440Mhz, 2480Mhz. Can you guide us how to enable PA without using Nordic stack file...
Hello,
I'm using a Thread Border Router built using a Raspberry Pi 3 and a nRF52840 Dongle. I followed the steps at this link: https://infocenter.nordicsemi.com/index.jsp...
Dear Nordic Semiconductor support team
Hi, I got your support using micro:bit with nrf52832 by RADIO in the past as follows.
https://devzone.nordicsemi.com/f/nordic...
I've noticed that Thingy:91 USB code has some issues related to proper handling attach/detach events resulting in incorrect response to usb host requests. Windows device manager...
Hello,
I am using the this sample;
https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160/udp_gps
I want pvt data instead of nmea data...
Hi,
What is the best way to read the async data received on a UART in to a buffer when ever there is an a byte available and in a separate task read the data from the buffer...
I need to include RTOS support in my NRF52840-based system. In order to obtain a good FreeRTOSConfig.h I've looked at the four examples in NRF5 that include FreeRTOS and,...
Hi,
I'm trying to make connection between nRF52840 dongle programmed with "examples/peripheral/cli" application and Windows 10 UWP "CustomSerialDeviceAccess" example code...
Hello
Currently I use the example "ble_thread_dyn_mtd_coap_cli_pca10056" and I would like that my application can detect timeout of the messages sent on the Thread network...
Hello, First of all, I hope you are doing okay about the corona virus crisis. I wish that you stay healthy and safe . Recently, I have been trying to configure ble_app_uart...
Hi Sir,
In the datasheet (V1.1), the table-145 shows the dimensions of WLCSP, but there is no tolerance of D/E/D2/E2
Could you help to advice what is the tolerance of...
I have a project where I am implementing an alternative logging backend. My design is modular so there could be multiple logging backends. Each backend is initialized with...
UPDATES after original posting:
I now remember having the same problem described below, once before on my windows installation. At that time I decided to switch and reinstall...