Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hello,
I am trying to find out where to put my persistent storage data in flash.
I have to set start_addr and end_addr, to use fstorage, but I dont know what addresses...
Dear Nordics,
i'm getting started with development on Laird BL651.
Issues as follows:
It appears to be neccessary to switch to internal RC oscillator and adjust the...
Hi,
We are facing an issue related to battery life. We are using sdk 15 and SD S132(7.0.1) and we are able to archived 30uA current consumption, but we want it near to 5uA...
Hello,
I am using SDK v11, SoftDevice v132 and Keil Uvision 5 to program on my nrf52832 SOC on the development kit(PCA10040) for our project. I need to save a few uint32_t...
I am trying to evaluate the nRF52840 and can't find the source code for any of the project - only the hex files to run applications.
Where can I find the source code?
...
Hi,
We have developed a mouse with nRF52832 using the ble_app_hids_mouse example.Now, I would like to add consumer usage into the hid descriptor to control media. So, I...
Hi,
I am currently working on nordic PDK. And I am interested in flashing nRF52840 through FTDI SWD interface. I want to know whether it is possible?
If yes, what will...
Hi,
We are trying to develop custom uart bootloader firmware without using MBR. also we are not using softdevice.
Here are some linker definitions which are implementation...
Hi! I'm working with a custom board, where pin p0.18 is connected to an external button.
I've read several posts, including this one which say that one must remove the ...
Hi, I'm unable to get a working example with the bootloader, softdevice and application. I'm following this: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts...
Hello There,
i have made an Selfmade PCBA with an nRF52810 and it is my first time that i am working with those Chips.
I have used the reference Design for this board...
Hi
I had a few questions about the nRF52833 SoC.
1. Is there a better way to transfer information through UART rather than using ( printf ) or ( NRF_LOG_INFO ) commands...
I have a similar error as described on https://devzone.nordicsemi.com/f/nordic-q-a/27626/access_model_reliable_publish-returns-nrf_error_invalid_param/109104#109104
I use...
Hi
I build the UartSecureDFU SDK to output a Window's EXE file, it send the upgrading aplication.zip to 52832 successfully in Window 7 System. But If build t he UartSecureDFU...
I have been debugging the TWI master of nRF52832 for a few days now and I have one more problem, which is very weird. For some reason, the master sends only the first read...
