Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
i want the ble_app_uart.c example to advertise also . so here i want to merge the ble_app_uart central +peripheral uart right ?
what are the changes i need to do
...
Hi Sir,
According to the datasheet of 52840 (v1.1), in the ref. schematic, the requirement of 32M is +/- 40 ppm.
In section 5.4.4.2, for the frequency tolerance requirement...
Hello,
Please comment on the expected difference in achievable range using 20 dBm vs. 23 dBm output power. Any details, assumptions, questions, etc. would be appreciated...
Hi, I'm looking for a more modern transceiver than nRF24L01 + and that works for the same. I am looking for a low or ultra low power transceiver that allows the implementation...
Hi, For my POC I use nrf9160 dk. Nrf52840 is used for scanning ble devices and nrf9160 dk is used for sending data to mqtt server (very similiar to one of the examples with...
Hello there!
We would like to use INT1 pin of ADX362 low power accelerometer on Thingy:91 board to interrupt nRF9160 (e.g. wake it up) when some motion is detected.
To...
Hello,
I am currently designing a new board using the nRF9160 chip and looking for an alternative component to use instead of the GPS RF Amplifier QM14501 and RF Switch...
I need to exchange data between nrf52840 and Linux PC. I see example project in nrf5SDK/examples/peripheral/usbd
Can anybody advise any example project for Linux C/C++ to...
Hi,
I'm working on nrf52840. As far as I understand, that device supports connection to peers with BLE 4.2 at least.
However, I'm able to connect via my phone, which...
Hi,
I have some questions regarding the state of the GPS functionality, and the future plans for nrf9160.
Will continuous GPS tracking while simultaneously using LTE...
Hi,
We are working with DK nrf 52840 and developing android app with nrf mesh library. is there a way to receive the feedbacks to the provisioners when any generic clients...
Hi ,
1-) Is there any dma half transfer interrupt ? if there is where it is in documents ? ( i check this link but i couldnt see anything about this https://infocenter.nordicsemi...
It is pretty straight-forward to use J-Link RTT Viewer on Windows (as described in the Debugging with Real Time Terminal tutorial ). Is there a similar viewer to use with...
Hi,
I am designing a bio-signal measurement circuit using nrf52832.
I wonder if there is any problem with the performance of nrf52 when using the sensor below.
Sensor1...
I can't comment in https://devzone.nordicsemi.com/f/nordic-q-a/56685/missing-ble_gatts_evt_hvn_tx_complete-events as it is closed but I am also seeing issues with the TX_COMPLETE...
