Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi ,
I am working on the project based on nrf9160.
Please verify it-
1. I want to print the current clock source of the board as board is initially work on LFCLK....
Hi!
I am feeling a bit stupid, since I know that I must have made a config error somewhere. I just don't know where. I am developing a BLE HID device using SDK 16.0 and...
Hello,
I have trouble with interrupt.
I use pin 16 to trigger interrupt signals from a sx1261 module.
It has worked well on example code with SDK 14, but for my projet...
SDK Version: 15.1 IDE: Keil Softdevice: S132 v6 Example: Blinky peripheral example slightly modified Q1. Does the Softdevice use RTC0? Q2. Does the App Timer use RTC1? If...
Hello everyone,
I am using the pc-be-driver-py library to start a scanning with IRK and I view the advertising events that I get. My peripheral is configured to do 1 advertising...
When i compily the SDK16.0.0 example project: iot_secure_dfu_bootloader_secure_dfu_s132_pca10040 i get error after Linker, saying .rodata and .data are too large for the flash...
Hi, As per our requirement, we have integrated GCP on thingy91 (PCA20035) and able to send and receive MQTT messages without any issues. But as part of FOTA implementation...
Hi,
I'm using the light switch example and lpn example from the Mesh SDK 4.1.0.
I have one Board as the light switch client (gateway), one as the light switch server ...
Hello,
I have included nrf_pwr_mgmt.h to the gpiote_pca10040 SES example to able to run "nrf_pwr_mgmt_init();" function.
I have added nrf_pwr_mgmt.c file under the nRF_Libraries...
Hi
I'm using nRF52832 and trying to make programming patterns via SWD myself, and want to make programming time short.
I have a question about flash programmng time via...
Previous versions of nrfx_spis.h:nrfx_spis_config_t had a "csn_pullup" field but the latest version does not.
The nRF52840 Product Specification is not very clear about...
I am trying to test this example on my nRF52840 DK and it is not working. Here i the steps I followed:
1) Erase the device by clicking "Erase All" under the "Target" menu...
Hi. I'm working on central device which is connecting to peripheral device. I used blinky example, modified characteristics to my needs and it works fine.
Now I try to do...
Hi,
I am developing a system with 2 nrf52840 devices, communicating via the NUS Service. I am programming both the central and peripheral project. I am using the NRF5 SDK...
