to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
I am creating a peripheral and central. The peripheral is done and appears to work fine. The central is in progress. It will use the serial port to communicate with a host...
I'm using the nordic SDK since version 8 (now version 16). For various reasons I always tried to not use the SDK and just programmed against the soft device API and programmed...
Hi,
I am implementing PPPoS using LwIP + FreeRTOS on nRF52840.
I have added LwIP and FreeRTOS which is available in " SDK/external/ " folder.
In LwIP I used LwIP's Sockets...
Hi,
I am trying to use nRF Connect for desktop with a dongle or nrf52 DK to connect with another board. When I want to get the value from the connected board, it would always...
We have a custom board based on the nrf52, We trying to integrate BLE functionality into our already existing firmware. I am able to create a custom service and characteristic...
ret is declared inside a "CRITICAL_REGION" which is a block, so not accessible outside that block to return: ret_code_t app_usbd_hid_generic_idle_report_set(app_usbd_hid_generic_t...
Hello, trying to make the leeap from nRFGo studio to nRFConnect, programming tool. I have connected to an old device programmed with nRFGo, and see the memory map below. I...
I am trying to debug an app error in my code. I have an app_error_fault_handler that starts like this:
But, the "Fatal Error in file..." line doesn't show the file...
DFU over serial
- Application alone - works
- Softdevice + bootloader works, but then doesn't respond to ping when trying to send Application image next
nRF52832 ...
Hello,
If the locators have AoA direction finding support ( nRF52833, nRF52833, nRF52820 etc , ) does beacon device require to have direction finding capabilities as well...
hello ,
I am using NRF52840 for my application, ESP32 as central and my nrf52840 as a peripheral . central always connected with peripheral. i can send data through central...
To the kind attention of Nordic support team,
I have been reading https://infocenter.nordicsemi.com/pdf/nRF52833_PS_v1.0.pdf product specification, where only
aQFN 73...
Hello everyone, I wan't to layout my own PCB board of nrf52840 ,is there any things need to be attention? By the way, if I'm not using Interface IMU to upload my programming...
When I have put the nRF9160 modem into mode 4 or 44, and then issue a status read AT+CFUN? command, the modem erroneously goes online. I have used latest and greatest modem...
I have the following code in my main.c file:
I also have mylib.c and mylib.h file. I want to move my function there. I tried the following.
mylib.c
mylib.h
I...
