Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
ScreenRecord_20171204_133336.mp4
I am working in sdk14.1 nrf52832 ble_app_hids_keyboard_pca10040_s132.
IOS and WIN10 on working ,but android no working .
here is...
Hi all,
We've tried to port IoT SDK features (IPv6 over Bluetooth low energy) to Nordic Thingy 52 .
As base, we use FW for Nordic Thingy 52 from GitHub
We need to send...
The last table on the S132 Specification BLE "data throughput" web page lists the maximum GATT Notification send/receive rates as 16kbps when using an event length of 2.5ms...
I've been following the instructions on how to test buttonless secure DFU without bonds using the Buttonless DFU Template Application page.
I followed the instructions...
I'm trying to port my project from SDK11 to SDK14.
I am having troubles understanding how the drivers supposed to be used.
In the files nrf_peripheralXXX_drv.c there is...
Hi guys,
has anyone had problems with: Cannot connect to J-Link via USB. message?
The device is alive and i can flash and connect to it from CLI.
Thanks
Hi guys,
Many thanks for the help before, I could now running example and change the parameters in the example code for my Taiyo Yuden nRF51 board.
Say, I would like...
Hello,
I don't know how to enable the notifications for a characteristic in the nRF Connect app for iOS. I have the latest version and I tried all the buttons but none...
Hi,
has anyone observed a behavior where the peripheral would be displayed as Accessory on iOS?
I'm seeing this occasionally with my S132 v5.0.0 peripheral, but can't...
In Android, is there any way to distinguish between an explicit disconnect requested by the remote device, and a disconnect due to loss of comms; eg, the remote device going...
Hi.
When I make flash bootloader_secure_ble, it does advertising well.
And I run DFU by making bootloader_secure_ble into .zip file.
However, it does not advertise bootloader_secure_ble...
Hallo,
I'm trying to create an application zip file to be uploaded with the DFU mechanism.
nrfutil pkg generate --help gives a list of options, but in the --sd-req part...
Hello,
I am using nrf52832 pca10040 with softdevice v3 of SDK v12.2, when booting my device tries to initialize the peer manager with pm_init() and this function is returning...
Hi All
I want to develop a PCB that has Wifi and BLE capabilities, to do this I would like to use Nordics: NRF51822 or the new NRF528, for the wifi side of things I want...
