I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I want to make a BLE peripheral device that only allows connections from authorized mobile apps, and an app that only allows connections from authorized BLE devices. What...
Hi all,
I'm having problem porting some project from Keil to SES since our project use absolute memory location to put some variable that will be share between main application...
Hi,nordics
I failed to find primary service successfully .The sdk version is 10.00 and I reffered to the example is ble_app_uart_c_s120.The pripheral is a gamepad .I can...
Hello there,
I was wondering if there's a known issues page fro SDK 14.0.0 (not alpha).
Issue #1: crypto compile error:
I ran into an issue compiling nrf_crypto.c
...
Hi everyone,
Does anyone have the beginner tutorials about BLE migrated to SDK 14?
I am specially interested in those about services and characteristics:
devzone...
what command did "nRF Connect" do, after I click "YES" ???
Im stranded in this example : “ble_app_alert_notification”
I don't know how to use "nRF Connect"
when I...
Hey Dev Zone!
I'm attempting to flash FW onto the Thingy via the nrf52840 dev board (which includes JLink). I connected P19 header on nrf52840 to P9 on the Thingy. I downloaded...
I am trying to run below 10 uA with code below while GPIO and uart are on. Sleep mode is applied (below 10 uA), and only wakes up when button is pressed (can be higher amps...
I have a micro connected to the PCA10040. I can use flow control with 5=rts, 6=tx, 7=cts, 8=rx.
Are these pins necessary or advisable for hwfc?
thanks,
Richard
Hello,
I'm having problems getting a stable channel from an Android device (LG K8) and the nRF52 development board. It is hard to tell whether which side is causing the...
I think the answer is mostly no. My application is similar to the Gazell sample projects, it does not use Softdevice. What are the steps to make my application to be compatible...
I loaded the bootloader on the device and it always advertises as DfuTarg even after loading a application that simply blinks an LED. It doesn't seem to switch to the application...
Looking to put this into our new consumer product, and working with a CE/FCC lab. They would like pre-qualification documents if any. I just need to know if they exist and...
Hello, I would like to copy ble_app_uart_c example to a seperate folder and work with that independently. I looked into the following thread and changed my include paths....
