Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
I'm develope some sensor with arduino primo, which use nrf52832 as a primary mcu.
I want to measure battery voltage level,and i find some example like:
devzone.nordicsemi...
I am using nrf52832_xxaa with SDK v11.0.
I have a requirement to write into UICR register APPROTECT to set its value to 0x00.
Is it possible?If yes, please provide a sample...
hi,
10040 nrf52dk
softdevice 132 v2.
keil ide
I am trying to read magnetometer values so that i can calibrate it using this method . For this to happen, i need magnetometer...
Hi guys,
I am using FDS module in nrf51822, sdk 11 to store and read data from flash. I have a problem about reading the data. In the documents, the function:
fds_record_open...
The problem
I am trying to build the examples contained in Bluetooth Mesh stack, but I get the following error when running cmake :
...
-- Found assembler: /usr/local...
we tried to configure two gpios as output{two separate controlling switch) at a same time.hex file formed without error but we are executing that hex file on nrf51422 dk board...
Hello folks,
I have been trying to flash/debug an example(blinky_blank_pca200006-nrf51822_xxaa) from nRF SDK installation but to no avail.
The hardware is actually the...
In latest release of MESH SDK v1.0.0, there is support for DFU Bootloader.
It will be helpful, when there is upgrade from firmware side to add new features & remove bugs...
Best way to send datetime from android app to nrf52.
Ultimately I am trying to send two datetimes from android app and compare them with the current time in BLE device...
Hi, I'm using nrf51822 module for bluetooth connectivity in one of my projects. I'm able to compile the code in keil v5 without any errors or warnings. But I'm unable to find...
Hello,
I want to allow users to change the device name as they like. I've been reading about it and I know what needs to be done, i.e. write to the device name characteristic...
i want to add a PA for a nrf51822 chip inorder to extend the coverage. i choosed a PA IC named RFX2401C.i am wondering how to deal with the TX pin and RX pin of RFX2401C.could...
Hello Guys,
I use BMD-350 rigado module for development. Now I want to programme it using raspberry pi 3.
I am using OpenOCD in raspberry pi to programme nrf52 chip...
