I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
My goal at the moment is to be able to configure my peer device which utilize ble_app_uart example so it would connect only to a specific master device e.g. android...
I am using BLEPeripheral and MySensors libraries and nRF51822 device(client side).
I want to change functionality, if I press key of nRF51822 device it should start to advertise...
I have a PCA10040 working with the mesh sdk.v1.0.0 serial example. I can do an Echo via the Python interactive_syaci and get a back a response. I have seen the documentation...
Hi Nordic
I am running ble and ANT + bsc code on our custom board. However, since the sd_softdevice_enable function does not return, I asked the question once. devzone.nordicsemi...
hi i am using nrf52832 soc with sdk14.2.0 ble_central_multi-link example with soft-device s132v5.0
i want to know that is that any way to set connection handle number can...
hi,
i am using nrf52832 mcu with sdk 14.2.0 and with softdevice s132v5.0.0 with ble_app_multilink_central example to connect with nordic thingy 52 as ble peripheral to...
Hi,
I noticed you have added C13 and C14 (12pF) caps. However, they are not visible on Infocenter's reference circuitry. What are these caps for and why they should be...
PDM Initialization normal,I enable PDM and start PDM sampl,I find not jump to NRF_PDM_EVENT_END irq,This is when the link is broken.I suspect not get data in RAM,can you gave...
Hello,
I want to add NUS service on the SDK_14.1.0_1 example called "ble_app_hrs_rscs_relay".
I added
uint32_t nus_err_code;
ble_nus_init_t nus_init;
memset(&nus_init...
Here: devzone.nordicsemi.com/.../group__ble__api.html
Choose to simply not keep track of available buffers at all, and instead handle the BLE_ERROR_NO_TX_BUFFERS error...
We plan on using 4 to 5 timers on our project. Each timer has different timer intervals (Example 1 minute, 50 ms, 300 ms etc)
We are trying to use 2 Timer instances and...
Hello,
I am working on example
nRF5_SDK_14.2.0_17b948a\nRF5_SDK_14.2.0_17b948a\examples\ble_central\ble_app_uart_c
pca10040\s132\arm5_no_packs/ble_app_uart_c_pca10040_s132...
Hello, I would like to know if there is any way to avoid bootloader start in secureDFU firmware transfer. All the checks on init file and control point are on the application...
My DFU is staying in the bootloader, even after successful download of the application package.
I have modified the secure bootloader for my custom PCB (removed the GPIO...
