I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
I've a silly problem I cannot get rid of.
I've started from nRF5_SDK_11.0.0 ( devzone.nordicsemi.com/.../) and now I want to implement it in another example but...
Hi,
I'm working on getting the ble UART example running. I flashed the softdevice (s140), then programmed the board (pca10056) with the provided hex file, and encountered...
we connecting our hardware nordic nrf52 to mobile application but its is not showing any Bluetooth enabled devices |
please let me know about sdk and how to test
Thanks...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi
I'm trying to implement the watchdog to my project, but I'm having some odd issues.
When I power cycle the device the watchdog works fine, but when I program the device...
I updated new firmware on nrf52. After that nrf52 was still visible "nrf Toolbox" Android app. It seems I didn't do anything wrong but when next time turned on nrf52 and scanned...
I am using nRF 52832 (softdevice v2.0). I am writing a code to get data via SPI and then transmit over BLE.
I have written my code and SPI is working perfectly.
But...
I'm new to using Nordic products and am trying to understand the difference b/t the soft device and the application in the context of the examples I'm running. Most importantly...
Hi, I have NRF52832 development board and NRF51824 beacon board. I want to dumb the code to NRF51 but i don't know whether we can use NRF52 DK to do the same(Supply to NRF52...
Trying to compile ble_app_cscs example, but have compiling errors in ble_cscs.c library.
Anybody have any ideas what is wrong?
Ubuntu 16.04, NRF SDK 12.3, GCC 7.2.1
Terminal...
Hi all,
I need to send the information from 2-5 sensors in a room. The sensors are placed 2-3 meters far from each other. Each sensor has a BLE, using a battery and generates...
I'm using the RSCS demo as the peripheral and the Relay demo as the central. I've modified each to use stored bond information if it is found in flash upon startup. I make...
Hello.
I am measuring the current of nRF 52832 using PPK (PCA63511).
I want to measure the current of nrf chip only with PPK.
The chip of nRF is PCA10040.
What...
Hi all,
I've bought an iBeacon Station NRF51822 like this one ( linksprite.com/.../index.php5 . My idea is using it as a temp sensor for my smart home installation. It...
