I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello,
I am using SDK9.0 and testing the LED_Blinky project with IAR tool, Evaluation kit. The application is executing and leds are blinking but I am not able to set a...
Hi, and thanks ahead for the help. I am working on receiving ble packets without using the soft device. I am able to transmit an advertisement with raw radio and pick it up...
Hi,
I am trying to write and update a record in flash but not receiving event callbacks FDS_EVT_WRITE and FDS_EVT_UPDATE. I found that i need to add the following code...
Hi there
Is there any PCA10040 simple demo IAR project? Just like print out "hello world" from any debugging uart? Base on this I can add in more functions gradually. ...
I am using clock signal from external RTC chip to clock NRF52832 at 32768 Hz through XL1 leaving XL2 floating. I have verified the waveform by the oscilloscope and set SRC...
2.4g ble work in 2 mode(not same time) when reset.
when I init 2.4g clock
void esb_clocks_start( void )
{
NRF_CLOCK->EVENTS_HFCLKSTARTED = 0;
NRF_CLOCK->TASKS_HFCLKSTART...
Hello everyone!
I have peripheral device with notify characteristic with 20 bytes length of value and connection time interval - 7.5 ms. So, I want to increase throughput...
Hi,
from the nRF52840's datasheet: Up to 4x SPI masters/3x SPI slaves with EasyDMA .
Is it possible to connect the nRF52840 as a slave with another microcontroller and simultaneously...
Hello,
do I need to do anything to accept new Connection Parameters as a Peripheral when the Central updates them?
I am seeing 'BLE_GAP_EVT_CONN_PARAM_UPDATE' events,...
Hi, guys.
I am meeting a terrible problem when using the SDK14.2 -> BLE\nRF5_SDK_14.2.0_17b948a1\examples\ble_central_and_peripheral
experimental\ble_app_hrs_rscs_relay...
HI,
I am using nrf52 with other mcu and sending scanned beacon to that mcu.
I have set baud rate to 921600 and transmitting data when mcu request.
when mcu request...
Hi,
We am using sdk 12.2.2 and nrf52. We are observing some strange behavior of chip. We have our own customized board.
The issue is mac address shown is different in...
Hi there,
I'm using a PCA10040 board, and the app that I am working on was originally built in SDK 11.0. I'm trying to send a stream of arbitrary bytes over USB using the...
Hello.
I am trying to download a program, but I get this error.
Beacon does not work when downloading in order of Application -> SoftDevice as indicated by the error...
