Hello,
I am using a nrf5340 dev kit. When I use SPIM the output from the pins gives the correct hex values but the output's amplitude is only around 100-200 mV. I know that...
Hi,
I'm using the nRF52840 with the SoftDevice for BLE. In my system, it's primarily a BLE transceiver controlled via SPI by an external TI MSP430. We're considering implementing...
Hello,
I want to request AGNSS information from nrf cloud services using my nRF9151DK board. As a first step, I flashed the nRF Cloud multi-service application onto my DK...
Hi,
I'm using cdc_acm to create two COM ports on a PC -
// USB support
& zephyr_udc0 {
cdc_acm_uart0: cdc_acm_uart0 {
compatible = "zephyr,cdc-acm-uart" ;
...
Hi,
We are having issues with this part bridging on our via-in-pads. We are using 2oz finished outer layer copper.
Do you have any footprint recommendations for 2oz copper...
Hello,
I'm looking for guidance and understanding of how to properly use the KMU and ITS for secure key storage of a key generated on device.
I see that typical ITS use...
Hi all,
Actually I'm building with vscode my firmware for a custom board build with an nRF9151 non secure. After building I got a merged.hex file, this is the file upload...
Reading the following post:
devzone.nordicsemi.com/.../
made me think that I could use either the nRF51822 or nRF8001 in my design. However, the following post:
devzone...
Hello everyone,
I have had an idea for a cheap homemade programmer for nRF51822. I don't know if it could work, it's just an idea I would like to discuss with you.
I...
I am trying to port the SDK 8.0.0 to use the IAR ARM tools and I am having a problem getting the linker to link the file system_nrf51.c that is called from iar_startup_nrf51...
Might I know the spec of the antenna which come with nrf51822-DK?
is it 50Ohm?
I try to use patch antenna on the nrf51822-DK. the perform i measure not very good at all...
I am using nRF51422 with a 16MHz crsytal, HMC5893, LED and MPU6500. I have noticed that the power consumption in IDLE mode is approx 1.2mA. This was originally at 6mA. I call...
I am trying to get DFU/OTA to work with the supplied sample Apps, so far no luck. I bought the nRF51 DK to have the hardware matching and tried with SD S310 2.01 and dfu_dual_bank_ble_s310_pca10028...
can you recommend me cloud provider which support Nordic, nrf51822->BLE->AndroidPhone->IoTcloud? e.g http://developer.garmin.com http://www.cumulocity.com or ...
Id like...
I wrote code to jump from application to bootloaer in softdevice 7.1.0.
It work allright,but other module of the whole program got a trouble like this
devzone.nordicsemi...
Hi,
The device may be talking to a TX/RX station (connected to the Windows PC via USB) that uses an nRF24LU1+ so I'm guessing I will need to use ESB for compatibility...
Hi,
Where can I find the instructions on what tools need to be installed to reprogram the nRF51822 beacons? I haven't been able to find it in the documentation provided...
Hello
I am working on a nrf51822 EK, i have worked out on BLE-multilink central and peripheral examples which were given in nrf SDK examples but it did not work.Please provide...
Hi
I need to configure my nrf51 tx power so that it is discoverable only at a particular range/distance.
for example: i need my device to be discoverable only within...
I'm using the nRF_Libraries software pack and found something in dfu_transport_ble.c that I'd like to change, e.g. the MANUFACTURER_NAME macro to say my own company.
This...
