در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
I have a need to maintain current state of my device along with other parameters, including temperature and hours used. If I update my pstorage page frequently, like once...
Hello,
I'm working on S110 peripherial <-> S120 central project using GATT. I have succesfully implemented S110-based peripherial device with some custom characteristics...
Hey All,
I am trying to create a simple data transfer system using a DFRobot Bluno (CC2540 chip) as the central device, and a Redbear Labs Blend (nRF8001 chip) as the peripheral...
Hello all,
In many thread I can read that it is not recommended to use the internal DC-DC converter to supply the nRF51822.
Can you tell me why it is better to use an...
Greetings all -
We have an nrf51-dongle for development and testing purposes, and are unable to connect to the device over USB with any of the Segger or Nordic tools. I...
Due to BLE's low range, license costs and unneeded complexity, I am looking in to pure radio RF. I am curious about ESB and Gazelle, and which one is good for relatively simple...
Testing OTA using nRF Toolbox on Android. Everything works fine, but for some reason the file selection is "stuck" in dropbox, i.e. I can not go up a level from dropbox, and...
my development environment is nRF-DK and IOT SDK
Q1 : IOT SDK Support Gatt Profile?
Q2 : IoT SDK Support DFU mode?
Q3 : in ipv6 coap server example, how i broadcast...
Hi!
I have custom board with nRF51822 and I need to communicate with serial flash W25X40 using SPI master example with SoftDevice enabled (S110 is used). I worked with...
Hello Everyone
i am using LINK LOSS service i would like to send notifcation to the peer device if the connection is lost and also if the connection is made between two...
Hi,
How to send large amount of data, using multiple characteristics? Assume that my data size 800 bytes and characteristics with notify property. I did splitting the data...
Hello,
I am looking for a way to send more than 20 bytes by using 'sd_ble_gatts_hvx' function.
I want to get the maximum debit that is in theory 6x20 bytes
Do I just...
