I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello,
I'm trying to create my own bootloader application that uses softdevice in IAR. I would like to know how to configure my project so that it writes 0x0003A000 to...
Hi all,
I've a problem using pstorage: after I execute a pstorage_clear, my ic (i have the pca10028 board) go crazy, the application I've write stop execute and I can't...
I have an application that advertises as connectable in BLE.
After connection and configuration, it should then disable connectable advertising and enable nonconnectable...
Hello,
My nRF51822 custome board has problem at first programing software with nRF51 DK. So I checked nRF51822 boot sequence and found diffence compare with nRF51422 which...
I develop my BLE with SDK 8.1 and softdevice 8.0, and I want to restore some data(about 50 bytes) to flash, can anyone please help to provide me an example for the entire...
I have had a look at you experimental implementation of DFU signing.
I'm very concerned about the code size. The old Bootloader used about 13KB and the new one with signing...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
I've got 4 services with 15 characteristics between them. Trying to add any more than that results in sd_ble_gatts_characteristic_add() returning NRF_ERROR_NO_MEM .
All...
Hi Expert,
I found a weird case that at my 51822 plaform with s110 enabled, if I define a global buffer like:
static uint8_t system_buffer[1024];
it obviously will...
Hi
The nRF24Le1 has 256 bytes in the infoPage for user data, starting 0x0100.
My question is how to write to that area?
Is it accessible from nRFgo Studio?
Is it accessible...
Hi every body,
Is there any way to increase the support packet per connection to more than 1 packet for S120 softdevice if i have just single slave and single master? ...
HI,
I have followed all the steps from devzone.nordicsemi.com/.../ and I can relay text between Termite & my iphone.
Can someone share a function / method which I can...
Hi,
I used the ancs demo of nRF51_SDK_7.2.0_cf547b5 to modify our application. It still work well, but sometime when I left the device and went out with my Iphone about several...
