Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Has anyone interfaced the nRF51822 to the CC3000 Wireless chip? I have started implementing the host controller functions in nRF51822. It would help me jump start if anyone...
I try to capture a BLE connection with the nRF Sniffer.
I can see the advertisement packages, but after i established a connection from an andriod device i didn't get any...
I want to drive motors at 40kHz and am wondering if I will be able to do this with the nRF51822. If not 40kHz, I might be able to go as low as 15kHz. What is the resolution...
Hi, I am using nrf51822 ble module. I want to have multiple such modules which could connect to a central device. How could I make it that the central device encourages only...
Hi, I am creating a custom service and corresponding characteristic. For that I am planning to use bluetooth base uuid (for confirmation : 0000 0000 -0000-1000-8000-00805F9B34FB...
Hi,
I`m working on our firmware for nRF51822 and I received the assert from soft device when turning off the global interrupts for our time-dependent procedure which have...
I am using PCA10001 board.
First of all i am unable to find nRF51 SDK.exe.
So i downloaded SDK form below link
link text
I changed device to nRF51822_xxAA.
Now i...
Nodic Semicond has made a nice step-by-step description for how to fix a corrupted infoPage.
It involves starting nRFgo Studio from a command prompt with "-defaultsettings...
Hi,
I want to make a connectable bluettoth transmission. I need 1 service with 3 characteristics, but for now I only want to see my service in app. It is possible to do it...
I have a nRF24LE1 processor.
We have an 'RF bootloader' which operates from the pc running a 'nRFUpdate 'Firmware over the air'' program using a dongle made by 'sparkfun...
i am running this code on my nrf.
const nrf_drv_timer_t TIMER_LED = NRF_DRV_TIMER_INSTANCE(0);
uint8_t flag;
/**
* @brief Handler for timer events.
*/
void...
I currently have both the nRF51 DK and nRF51 Dongle plugged on my PC. In Keil, when I try to load my program into the nRF51 DK I get the following error: "No JLink is selected...
HI People,
I face a problem when I do an OTA DFU from APP to APP. I compiled ble_app_hrs S110_with_dfu example fro sdk 9.0.0 and did OTA dfu. Now the device advertises...
I'm in the middle of putting a NRF51822 device through bluetooth certification. The test house has asked that I have modes where the radio is transmitting on certain frequencies...
