Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi,
I want to design one BLE braodcaster and one BLE observer using nRF51822 chip.
What should be the advertising interval time and receiving interval time (with receiving...
Hi:
I am using the ANCS from SDK9.0 ,SoftDevice8.0 and iOS8.1.3.
Every time when I run ANCS, SPI will often crash.and error codes is:NRF_ERROR_BUSY.
Don't know if...
Is there any extra requirements When a Android APP connect to my Ble Decice? I want connect to my Ble device(51822) by my Android APP(EZ-GUI Ground Station V3.208.208), But...
We have the bootloader working over serial at UART_BAUDRATE_BAUDRATE_Baud38400. We took a big leap and tried it at UART_BAUDRATE_BAUDRATE_Baud230400 and it failed. We will...
Dfu not working when i try to upload my custom made application second time.
nrf51422 sdk v8.0 and softdevice s110 on pca10028
the steps i used to do dfu are as
1)programed...
Dear all
I have some questions about nRF51822 bluetooth smart beacon kit, I read the User guide, but I can't get information about the following questions:
1、what is the...
I want to change bootloader start address BOOTLOADER_REGION_START to 0x33800 to store user data and DFU. But when I only change BOOTLOADER_REGION_START, my device can't work...
Dear Developerzone Board
Does the nRF51822 Sniffer just start with the conversion over all advertising channels or do I need to send a start command? Which command set...
The ENable pin on addition hardware component requires "floating" to power on, and drive low ( less than 1.25V) to turn off.
Unclear based on my understanding of the chipset...
Hello
Is there a way to stream data from one nRF51 device, to a second nRF51 and have the received data sent over UART to a host PC? Basically in my setup, I have a custom...
I'd like to understand why BLE_GAP_ADV_TYPE_ADV_IND is used while using a whitelist.
An example application that does this is the ble_app_proximity app. You'll see the...
Hi.
I need to use multiple SPI devices and I'm not sure which is the proper way to handle this, should I open/close each time the SPI port with different SS pin configurations...
Hi,
I wonder if nrf51822 has a clock inside it.
It doesn't need to be real clock
but It's important to me.
I store datas on flash and send it to the phone when it...
