Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi all,
I am trying to update the bootloader, softdevice and application all in a ZIP package through DFU, and at 99% after upload it stop and throws the error:
...
Dear Engineer:
I am a developer of the nRF51822;Some costomers want to send a large number data over the bluetooth,So they require a high quality in speed;I want to know...
Hello,
I've noticed that it is quite hard to set up an Eclipse development environment and I want to try to make a package of everything that is needed for developing with...
Hi. I want to attach a sensor with SPI slave interface to the nRF52 Preview DK (PCA10036) using the SPIM1 with EasyDMA. Below I have two related questions:
In PAN...
It seems that in SDK9 the APP_BUTTON_INIT() macro has disappeared, and with it the extra argument that determines whether the scheduler is used or not.
However, the documentation...
Hi,
I want to develop one FOB key which will be in TX mode only to transmit a key continuously or at specified interval at ultra low power mode and powered by CR2032 coin...
I'm having really terrible RF performance with a PCB I've designed using a nRF51822 QFAC, Johanson 2450BM14E0003 balun, and a PCB IFA (from TI DN0007: www.ti.com/.../swru120b...
I would like to create a large “virtual” read only characteristic that does not fully exist in memory. I understand that large characteristics are transferred in chunks of...
I am trying to enable a critical section in handler. I need to update a sensitive global variable when a button event occurs, and the fact to enable/disable the interrupt...
I have nrf51822 and I use latest SD130. I scan nearby ble devices. In my case they are iPhones. When one device is in rage then I connect to it and start scan again and keep...
Hello to everyone!
So, now I try to enable a DFU for nrf51822 (S110 7.3.0)and have some problems with it.
I can't find a good example project including DFU, all that I...
I've created a simple test to demonstrate pstorage store/load for 64 pages of 1024 bytes each. To allow 64 flash pages I set PSTORAGE_MAX_APPLICATIONS to 64. Each page stores...
I've been following the custom service nAN-36 instructions and have it mostly working on my PCA10028 board, but I have two problems that I just can't figure out. I'm pretty...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
