My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
I am developing a custom board using nRF52810.
SoftDevice S112 6.0.0 and SDK 15.0.0 are in use.
I want to know the maximum current in Idle state .
Current measurements...
Hi all,
I am currently trying turning off the active time, so that the nrf9160 immediately goes in power save mode after RRC Connected Release.
If I send the command ...
I connect VBUS to VDDH, and use a USB cable for power supply(high voltage mode), but I cannot download firmware into the 52840.
Unless I power the 52840 from the VDD pin...
Hello,
I'm a teacher. I use the microbit card that loads one of your components. Nordic nRF51822-QFAA-R rev 3 Could you tell me if this processor is based on a Von Neumann...
Hello, just a few quick short questions regarding nrf52 devices:
Do I have to configure and initialize them before using?
Which function should I use? I...
Hello, I working for TSS.se now selling 100.000 temperature-loggers annually. We aim to develop a new IoT based logger based on nRF52832 as a replacement.
Issue-background...
Hello,
nRF52840-DK
SDK 15.3.0
SoftDevice: s140
IDE: SES
Example: Flash_fstorage_s140_pca10056
I do not read back the expected value in the example. The terminal...
Hi, I am trying to do DFU OTA. I am using SDK v16.0, s140_nrf52_7.0.1_softdevice.hex, SES and nRF52840 dev kit. I am finished with my application and it functions as expected...
Hi,
We are a module manufacturer. We are making modules based on WLCSP, QFN based nRF52840 SoC.
Can you please provide software(preferably GUI) available for module FCC...
Hi guys, i can't figure out how to create an event handler in my Mesh Client.
The functionality of this handler should be to set a flag on the 'NRF_MESH_EVT_TX_COMPLETE...
I used keil v4 compile the following project F:\nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral\ble_app_uart\pca10040\s112\arm4\_build get file nrf52832_xxaa.hex of size 101kb...
Hello ...
I'm porting our product from RF Digital's Simblee to Laird's BL651 (nRF52810). A phototransistor measures light, is connected to an analog pin, and is sampled...
Hello guys! And girls
My project is working as expected in SDK14.2. I'm updating adv data (manuf. spec. data) without any problem with this function But in SDK15 the function...
