Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
I'm using a buffer size of 64 bytes using function
nrf_drv_uart_rx(&app_uart_inst, rx_buffer, 64);
When I receive only one byte packet from the remote, I get EVENT_RXDRDY...
i want to use pwm of rnf52810.but i don't know how to recognize what pins is pwm.
what pins in 52810 i can use wire to connect and then use it's pwm function?
or i can...
Hello, I try to import big project from Keil to SES. The main idea is to move to better IDE and use the same compiler ARMCC provided by Keil (license is present).
I have...
I am trying to using ceedling with FFF to create mocks of some of the NRFX HAL files. However, when I run ceedling I get some very weird errors. I've taken the `test/include...
Hello,
Below are details of my setup:
Peripheral: nRF52 DK
Central: One Plus 5 android phone
Sniffer hardware: nRF52 DK
Wireshark version 2.4.2
On Wireshark, I...
Hello everyone,
Some info about my setup: OS: Windows 10 IDE: SEGGER Embedded Studio v4.22 (64bit) HW: nRF52840 Dongle rev 1.2.0 as Coordinator, nRF52840 DK rev 1.1.0 as...
Hi,
I am trying to implement OOB pairing via USB. I have the USB portion sorted out. The idea is for a peripheral device to send over OOB data over this medium, which then...
I have problem with send hex on flash memory in dongle. I erase fllash than plug out dongle i know that i shuldn't but raspberry sey, he can't erase falsh. Dongle has 1.8V...
Hello,
can you please advise if the GPS antenna for the dev kit nRF9160-DK would also be available separately?
Our customer received this kit with version 0.8, which does...
Since APIs have changed as new nRF5 SDKs have released from time to time, it is not clear how custom service can be implemented on BLE peripheral for nRF52840 (pca10056) S140...
Hello All
I try to port the blinki example (with softdevice s130 2.0.1) to my Hardware with the nrf51822_xxAA.
The application will run without Softdevice.
But as soon...
Stack violation: stack pointer outside stack area.
Cause: Data bus error (PC value stacked for the exception return points to the instruction that caused the fault).Bus...
Hi,
I have PCA10000 Revision 0.9.0 nRF9160 Board with external antenna (Molex 206640)
I try to make GPS work. Here is my step:
I compiled GPS under samples ..\root\ncs...
I followed the start up procedure-
All OK, but my nRF9160DK doesn't connect to the network.
Only led3 is blinking.
I think iBasis-eSIM is not enabled in my area.
I...
Hello,
I need my timer to work at 9600 bps frequency. So accordingly my frequency is 16MHz and to get 9600 Hz I calculated the prescaler to be 10.7 ~ 11. But in the timer...
