Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
In my project, I typically have 20 central connections to the Nordic device. Occasionally, I need to allow a phone to connect to the device using a peripheral link. When this...
Hello,
From the documentation I read that Softdevice can support maximum 20 BLE concurrent connections. How does Nordic determine this maximum number of 20 and is this arbitrary...
I see the SWD debug port is a 2-wire protocol, SWCLK and SWDIO. My debugger device has two additional pins, SWO and nReset. Are these two pins required to debug and program...
I PURCHASED A SIM OF THE THINGHS MOBILE BECAUSE IBASIC DOES NOT WORK.
I HAVE LAUNCHED ASSET TRACKER AND THE NRF9160 DOES NOT CONNECT. LTE FLASHES IN YELLOW.
IS THERE A...
I was checking DFU through serial usb/uart on the following link:
infocenter.nordicsemi.com/index.jsp
I want to double check if this entire project is for programming...
Hi,
While linking I am getting the following error on Nordic SDK 16.0,
XYZ.axf: Error: L6218E: Undefined symbol nrf_ble_gq_conn_handle_register (referred from ble_db_discovery...
Hi everyone,
I am new to segger embedded studio. I want ibeacon firmware sample code to advertise uuid, major, minor, tx power, advertisement interval. I want to change...
We're developing a product where a single NRF52840 board - lets call it the central- serves as the focal point for multiple NRF52840 boards spread out across an area - lets...
I am not able understand the difference between APPROTECT and BPROT . Can you please clarify ? and if we enable the protection then how to disable it again whenever we want...
I've seen many posts about LL_LENGTH_REQ causing disconnection on certain Android phones and the solution from Nordic is to add a 100ms delay. Can someone from Nordic definitively...
Hi community,
in our setup we use the LSM6DSL IMU using TWI. First we initialize the TWI peripheral, then we configure the IMU. After that we initialize PPI to automatically...
I am trying to build the project "thingysdkv210" which is downloaded from https://www.nordicsemi.com/Software-and-tools/Prototyping-platforms/Nordic-Thingy-52/Download#infotabs...
nRF52 DK
HTS example
I added app_timer_stop_all() in the ble_evt_handler() of main.c, under the case of BLE_GAP_EVT_DISCONNECTED, but the battery service timer still...
