Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
HI,
i have made 3 customer board
they all use the same spi flash mx25v8006e
and the first two board have the spi pin : sck 3, miso 1,mosi 0,ss 2
but i change the design...
All I want to do is use the "Advertiser" tab in my nRF Connect android app and force it to broadcast using a custom 128-bit UUID.
I am struggling to figure out how to do...
I have tried combining a working SDK16_98a08e2 MPU6050 example with the SDCard example in the same SDK, however it seems they are incompatible because the MPU example uses...
Hi,
I am developing a device with nrf52840 soc, I need to know that there is any unique and unforgettable id in this chip that with that I could differentiate between...
Hi, Just wanted to pass this along... with the latest Raspbian (09/26/19) the thingy52 will consistently disconnect after about 90 seconds (+/- a few seconds). You can easily...
Hello,
I have two boards of nRF52840, one being central and the other is peripheral. On the central I've put the code from ble_app_multilink_central and on the peripheral...
Hello,
I see this type of query or GATT error has been asking continuously. I have gone through all the same Q&A but not able to solve my query. I have tried all the possible...
Hello Nordic support,
I was referring to the RTC example in nrf52 SDK where an interrupt is triggered on Compare Counter event. In the example, the interrupt is triggered...
I am trying to make custom BLE service to send the data from one nRF52832 to another nRF52832 but we followed the below tutorial "Bluetooth low energy Advertising, a beginner...
Hello,
We are developing a device that needs to get local binding info on init to see if it needs to send data or not to an on/off server in a remote device.
Is there...
Hi,
I'm using nRF52832 board and I'm integrating the Bluetooth beacon sending in the Bluetooth Mesh example. I've edited the Mesh Beacon example in Mesh SDK v4.0.0 with...
I am working with ble_app_uart example. I have added a new folder by name custom_folder in $(SDK_root)/, the same places where folders like library, softdevice, ble, boards...
Hello, currently im using feather nrf52840 board in arduino environment. I made some tests with BLE with TX power at 8 dBm and when boards are at line of sight signal is good...
In the SDK it suggests we use those new nrfx drivers, and says the legacy will no longer supported in the future. However, in the examples of the SDK, it uses the legacy driver...
hi
i am using sdk for mesh v3.1.0 i get my data from the uart and sending it over the mesh. i have been getting an error within the function net_state_seqnum_alloc() that...
