I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I have 2 questions, both related to power/current consumption.
My setup is a custom board, with mfw 1.1.0. I havev arlier seen current consumptions in the µA-range. I now...
Dear Nordic Support,
I am doing some test on the Thingy:91 v1.0.0 in Vietnam. I am running 2 examples: Asset Tracker with NB-IoT + GPS and GPS .
When I use the stanalone...
Hi,
How i can make the low power node to wake up until get acknowledgement . Please tell me how many ways we can try...In my project i used initiate_friendship() function...
It appears to me that the zb_zdo_ep_resp_t struct is missing a variable value attribute since the actual list of end points is missing. Should it not be similar to zb_zdo_match_desc_param_t...
Hallo All :-)
As an enthousiast hobbyist I've developed a custom board around an nRF52832-CIAA. When I started testing with a BLE secure bootloader from the SDK16 examples...
Hi,
I am currently working on " asset_tracke r" application. Actually, I need to read 128-bit UUID values of the BLE ibeacons present nearby the board (PCA10090) to be captured...
Hi, everyone!
We try to use THINGY:52 board for debug our MEMS lib from external sensor. But before use external sensor (i2c bus) i can't burn standard firmware that compiled...
Hi all,
I'm working with the reception of 802.15.4 packets on nRF52840 for which I have configure the radio as follows:
In the application loop we have:
...
Hi,
I am using nRF52 SDK v16 and I am wondering where one can find relevant information regarding peripheral event handlers.
Here are a few puzzles I have for now:
...
the central(phone) connected my board,when i call sd_ble_gap_disconnect ,sometimes,not every,return err_code =0x00000008,and not firing BLE_GAP_EVT_DISCONNECTED,also not advertising...
Hello All:
I am working on the time service of NRF52. As I know, there are two standard profiles refer to the time service, one is CTS(Current Time Service) and the other...
Hi All,
I am doing a BLE Mesh development project with nRF52840. SDK version: nRF5 SDK v15.3.0 & nRF5 SDK for Mesh v3.2.0
Case 1:
- IDE: Keil
- Example tested: nRF5...
