I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
Hi,
I am using ncs V1.0.0
When I configure P0.5 as input it takes 37uA current. (Interface with PCA63548 / LIS2DH Interrupt)
If I not configure the pin as input getting...
Hello .
We have an issue with the SPI channel.
We found out that when our GPIO config as SPI the CS drawn a lot of current when it connect to the slave device device AD7770...
Hello,
I am working on pc-ble-driver-py to design a central (using a DevKit with a nRF52832). At this point I am trying to perform a phy update procedure but I see it is...
Hi Everyone,
I am using PSM mode in my program and want to send data everytime when modem wakes up from sleep(PSM mode). I also want to turn off/on UART only when required...
Hi,
During startup the nRF sniffer extcap script does the following:
Which (at least on Linux) breaks applications having open serial ports.
Why not instead use...
Hi all,
I have mqtt sample on my board, after I added MCUboot module from Configure nrf Connect SDK Project, when I try to debug, it gets stucked at :
#elif defined(CONFIG_ARMV7_M_ARMV8_M_MAINLINE...
hi,
nrf52840 BGA footprint P0.22 config as UART0 RX mode, don't receive any data, but config as other pin P1.06, work normally.
and I also test QFN footprint with nrf52840...
I have nrf52832 platform and my version of softDrive is (nRF5_SDK_15.3.0_59ac345). I red a lot of documents and tech support like these links but couldn't find my problem...
I have another MCU on the same board as the Nordic 52832. The firmware update image for the MCU is about 50kb in size, so instead of adding a parallel DFU for the MCU through...
So currently I am using a 5 second repeated timer to run all my operations but there is a draw back to this that the max accuracy I can achieve is of 5 sec, like if I want...
Hello!
I have 18-bit sensors with SPI and I2C , which I intend to use in a wireless array.
I need to choose equipment and topology (star, scanning mode?), enabling data...
We had a custom board made with the nrf9160 and I noticed I was having trouble communicating with the sim card on my board.
We have been testing i2c, spi, number of peripherals...
I am trying to run the hci_uart sample on my 9160 DK but I am facing problems uploading the code. I am able to run the AT client and Asset tracker just fine. As soon as I...
I've been attempting to optimize my scan and connection intervals in order to maintain the highest percentage of time scanning while maintaining connections, following the...
Hi,
I am developing a Linux PC application (central) connecting with nrf52840 dongle with s140 v7 flashed on it (for long range support). I am using pc-ble-driver v4.1.1...
