Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
Hi am trying to use Nrf54l15 as a controller with an external host for the Channel sounding feature. I can receive CS subevents from the NRF controller, but the same thing...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Environment
nRF52832, nRF5x-Command-Line-Tools_9_7_1_Linux-x86_64,
Problem:
Programming of Softdevice, Application and Bootloader with nRFGo Studio works.
Programming...
Hello,
As I understand it, bluetooth declaration IDs can be used for multiple products as long as the products all share the same QDID . In other words, If you do it right...
I have been following the tutorial devzone.nordicsemi.com/.../ on how to use eclipse but in the makefile part im getting this error. I'm using sdk v11. I have used sdk v14...
hi,
i doing a program to receive multiple service data from nrf thingy 52 to nrf52840 central device.
as of now i have implemented weather service, motion service and...
I have been trying to integrate support for multiperipherals into my application, but am continuing to get errors when attempting to start advertising after the first connection...
As I don't know much about audio,I have trouble with the gain of the pdm module in nrf52832.Now
I have used MP45DT02 as the digital microphone,but I just can't understand...
Hi, I've searched and googled through this site and made sure no one asked this question before.
In core\Bearer_event.c, there is this function:
bearer_event_flag_t...
I'm trying to connect two nRF5 devices together, Central and Peripheral, and use a custom BLE service that I have written that has a custom 128 bit UUID.
I'm in the process...
Hi,
We are sending a data using Nordic UART Service (NUS), the data is transferred over BLE as a Indication.
From Message Sequence Chart in Nordic Infocenter
Here...
I am researching OTA procedures and I spent more than a few minutes wrestling with flashing soft devices and bootloader code to the nRF52_DK.
What I found is JLINK seems...
When adding extra buttons on breadboard for NRF52-DK do we need to use resistors OR i can directly connect one leg to GPIO pin i.e 30 and another to gnd.
I'm trying to use the nRF24LU1P as a standalone 8051 with the nRF24 radio inside. I provide 5v on the USB connection but no host connection. I am trying to operate in PRX...
Hello,
I'm using the nRF52840 development kit with the "« ble_app_att_mtu_throughput" example with version s140 6.0.0-6alpha.
What's the bitrate used in the long range...
I'm using nrf52832 in my peripheral device, I want to secure its connection via any authentication is there any method for that?, also I need to encrypt its data(characteristics...
Hello,
I'm working on a bootloader based on the examples in SDK 13.1. As we have expanded its functionality, I'm now wondering what happens when one of the steps in the...
