I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
I'm working on a product that is somehow related to geolocation. As part of it, RSSI measurement is sent back at high frequency to the central. Currently based on nRF51822...
Newbie here hoping to get some direction on how to properly setup a timer to have a timestamp displayed for DEBUG messages. I am working on a PCA10040 board. I tried looking...
Hi,
I have some basic doubts in installing the power profile on nrf52Dk(nrf52840). I'm trying to use it on my central device which has its application FW running. I have...
what is the sending data rate of the sd_ble_gatts_hvx() ,why i use sd_ble_gatts_hvx() send data 600Byte per second, it lost data again . it can be use yes or no ?????????...
I can copy a Hex file from a Mac to the mbed USB drive and the code executes correctly. However, if I upload the hex file from any windows PC in our office (Windows 10) the...
Hello, I am trying to generate pulses with the nRF52832 chip.I created a basic setup for test purposes; I simply connected a LED to the PWM output, but even though I put 0...
Hi,
I have designed the Circuit using NRF52832 BLE and AT8010-E2R9HAA RF ANTENNA and tuned the circuit accordingly. Since the antenna was not available so I placed other...
I'm relatively new to development on the nRF52832 and I'm trying to find information on how to use the sleep mode with the SAADC.
Goal: The micro should be in sleep mode...
Hi,
I am trying to create a BLE node which can perform dual role(advertising/scanning) to create mesh of multiple nodes. I am planning to do it with the help of timer....
the project has a problem with DMA,the detail is:
on the board,NRF52832 and extern chip communication with i2c bus,the chip through a pulse wake up nrf52832,NRF52832 start...
I have NRF51822 Controller(custom board,S110) used to send some sensor data. i can able to receive data in android and ios. now i want to communicate to Laptop which has internal...
Hello Everyone,
I am new to nrf51822 (using S130). I made some custom service that accepts float numbers.
This might be noob question: I want to send float values from...
We are developing a custom ble service and profile however having printf makes our lives that much easier so we are trying to incorporate it purely for testing purposes. ...
Hello,
I'm trying to optimize my application :
I have a central (nRF52832 s132) which communicates for a short time to a peripheral (nRF51822 s130) and then disconnect...
Hi
I'm trying to register an fds_evt_handler() in SDK 14. I have several questions:
Should I be registering fds_evt_handler() with NRF_SDH_SOC_OBSERVER or NRF_SDH_BLE_OBSERVER...
