Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hii,
i am using ble_app_hrs_c_pca10056_s140 and when connected to one particular device i am able to get battery level of advertiser but i what advertiser's device information...
Just like the title, I want to know what they are, because I recently in looking for nRF5 SDK for Mesh often see the nRF OpenMesh related information, so I think they are...
Hello,
I am trying to use ArrayList for EasyDMA along with PPI but I am not sure whether or not I am configuring it properly to be used with the SPI interface.
So far...
i am using ble_app_hrs_c_pca10056_s140 and when connected to one particular device i am able to get battery level of advertiser but i what advertiser's device information...
Hello experts,
I am getting into the word of Nordic and hence here is my first question. Kindly help.
Software version: SDK-14
Hardware revision: nRF52832 DK (PCA10040...
Hi,
The SoftDevice uses the GPIO pin and port abstraction to configure and control IO's. When developing in Thread, how does one access and control the nRF52840 GPIO's...
I call the following function to delete old FDS records before I write a new record. It works well if I have only one old record. But when there are multiple records, it stops...
When I use nrf_drv_gpiote driver by sdk8.1.0. with softDevice 8.
I got HardFault_Handler when run in
handler(pin,polarity); in the GPIOTE_IRQHandler
How to deal...
Hello,
I use stack S110 V7.1.0 on nRF51822 (the device is a remote with 4 buttons).
Currently the remote send advertising frame with the pressed button into the data,...
I am writing code for nrf51822 with softdevice and an accelerometer is connected to the nrf chip. The accelerometer provides interrupt to nrf chip over GPIOTE whenever there...
Hi Nordic,
I am trying to extend DFU feature to my beacon application. Please help me with how to go about it. I went through the given tutorials on DFU/OTA, but I haven...
Hello sir,
I have develop my BLE_UART code is working fine with nRF52832 DK board but when i flash into spark fun nRF52 is not working. But i able to flash into Spark fun...
nrf51-Dongle keeps on connecting and disconnecting (to the PC) when inserted into the usb port of the PC.
Also it is getting heated up upon keeping it in the usb port for...
i am working on aes_ccm with '802_15_4_lib_keil.lib' , and i have build the target,but the result is not right. since there is no example with this lib,
now i have a big...
