Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi,
I posted recently about having used the app_uart driver and having problems with an overflow breaking uart receive ( devzone.nordicsemi.com/.../)
I decided to try...
Hello, I have an error while building the project "ble_app_hrs_rscs_relay_pca10056_s140" with sdk14.0.0 on segger embedded studio 3.26 and gcc/clang.
When compiling nrf_atfifo...
I have newly purchased the nrf52 Development kit . Does it contains any pre-loaded firmware detectable on the ble scanner or nordic connect device, becasue I cant see any...
Hello,
I would like to use the button handler library (app_button) from the nRF SDK on my nRF52840 to detect pushes on pin P1.05. However, no events are detected when the...
HI experts
I have a nRF51-DK board. I have flashed it with S130 softdevice. I have also flashed it with BLE_APP_HIDS_KEYBOARD application example. I have made little change...
/DfuImpl: Setting object to Command (Op Code = 6, Type = 1)
Something like this printed in log cat and after this app is stuck ..rest of the process not execute..
If the nrf51822 device goes out of range then comes back in range, the application automatically reconnects with the device and tries to read a particular characteristic....
Hi,
We have a set of connected devices in a building of around 22 floors, may be around 6000 devices, can it connected using a nRF52840 Mesh network? Please let me know...
I used the 52810 board, with the SDK14. I modified the 52810 according to the official website related to the relevant definition. I can run the code but it does not print...
I've been searching and wanted to confirm that in SDK13, it's still on us to implement a timeout if a device is placed in DFU mode? As others have said, this just seems such...
Hi,
I am planning to enable autoconnect feature in our app, the same way it is done in nrf-connect app. Is there any way to get the code for nrf-connect app or any other...
Hi there, I was trying out the ADC example which is sampling 10 times the ADC and then generating the event NRF_DRV_ADC_EVT_DONE to process the data.
I extended the handler...
Hi, Im using Nrf51422 DK board.
When I try the ble_app_multilink_central example in the SDK12, it works on the DK board.
But it does not work in NRF51822. (NRF51822 QF AA...
Hello All
I planning make DFU over the air.before going to this experiment i want know some information
Any Soft device is fine or Required specific SD
...
I would like to disable the secure timeout in the bootloader for a specific condition.
I am using nrf52832 chip, sdk 12.2, softdevice s132 v3.0.0 with secure bootloader...
