Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Greetings, we're currently working in an application where we need to connect different peripherals to a nrf52832 for a wearable device. Each of these peripherals uses a different...
Hi:
i write very simple BLE App, it used open link. No security/encrypt. 1 service with 2 characteristics.
tx(serviceTXID, rxBuffer, 0, sizeof(rxBuffer), GattCharacteristic...
Hi there,
I wonder why I have to flash my nRF51 DK using mbed build first to make the SDK build work?
I received my 2 nRF51 DK today and I tried the first one in the...
Hello
I am new to Nordic's product line. I would like to know if there is a recommended Bluetooth 5 SoC for wearable products that require years of battery life. For example...
Hello, I am trying out my pca10028 board, with s110 and my updated ble_app_uart expample. I am trying to detect a link loss: board advertises as peripheral connects with android...
Hello,
I work on module BLE LAIRD BL652 and I'm a BLE peripheral. I have tried to make a BASIC program for advertising while in a connection but without success.
As...
Hi,
i am creating a new project iar workbench 7.8 with SDK V8.1.0 and softdevice V8.0.0 using custom board nrf51822 ic revision 3 (QFAAH00),clock source as "NRF_CLOCK_LFCLKSRC_RC_250_PPM_8000MS_CALIBRATION...
Hello Sir,
I am designing PCB using nRF52832 SoC it is very small and operated on AA battery source.
So please recommend me for reverse battery voltage protection diode...
Hi Guys,
Me again. I was thinking someone could provide some suggestions on my understanding of the BLE connection ( porfile, GATT, characteristic,value, etc...)
I finished...
I had successfully write a structure data to fds. After which, I would like to update the same file and record key with new values of a structure. After updating, I will read...
Imagine I have developed a MESH made up of 50 Relay Nodes and I say only Relay Nodes because any of them must be able to relay and also able to initiate a message. In my application...
Hi,
I am making a GPS tracking system using NRF51822-QFAC. I am using 2 UARTs, one of the (external) GPRS IC and one for (external) RS485 communication.
The UART peripheral...
HI,
I tried to compile Thingy v2.1.0 with keil. And sereval file are missing.
Actually i work with your SDK 14.0.0, i find so many missing file, but not all.
Can...
Hi,
I am currently testing with a USB MSC example .
FATFS_QSPI is disabled because the file system is not used,
Subclass has also been modified to 0x06 -> 0xFF.
...
Hi,
I am implementing experimental_bootloader_secure_usb code example on PDK PCA10056 V0.9.2 using Sdk v14.0 and also tested with Sdk v14.2 but in both cases Windows 10...