Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
I need to us an external RF amplifier that requires TX and RX control lines. I'm looking for a way to tell when TX starts to kick the unit into TX mode. I also need to know...
Hi,
We use NRF52832-based BLE module running serialization (SDK 14, softdevice 5.0.0) and STM32F407 MCU running application firmware on a custom board. The project is created...
Hello!
I am looking examples for nRF5_SDK_14.1.0 (For example - ble_app_eddystone )
I need read all attributes with ATT_Read_Blob_Req command.
I can read Device Name (0x2A00...
Hello,
I am using nrf 52832 and sdk 14.0.0. and i am using "ble_app_uart".
I am developing an iOS application.
Its purpose is character transfer.
I want to transfer...
Hello,
I did a quick test using 2 nRF52840 kits to measure the change of the RSSI value based on the distance and the used PHY layer.
For each test, I configured both...
I was reading through the documentation and it mentions you need;
One PCA10028 or PCA10040 development board for the client.
Three development boards or dongles...
Hi,
Is anyone successfully using MMD with the nRF52840 PVK, SES 3.3, recent SDK (e.g., 14.1.0) and S140 softdevice?
I followed the steps in this blog post both on Win10x64...
Hi.
Our company is designing a new device using the nrf52832 chip for BLE communication with other equipment from our Company.
Does the chip come with a factory preprogrammed...
Hi
We are developing ble peripheral application for the nrf52832 using SDK v13.0.0. and everything was working correctly until we tried ble connection with the iphone 7...
Hello Sir,
I have developed my application using nRF52832 chip with BLE connectivity. My device is battery operated and hence i am looking for WiFi chip with small size...
I have three questions about using AES CCM encryption by S132 timeslot API.
Is there an example value for the time request parameter in sd_radio_request(), when using...
I'm working with uart on the nrf52832 and I'm facing an issue related to the baudrate.
In this post a formula for calculating the baudrate given the register value is given...
I'm setting up the message structure for usage in a sensor Model. The sensor readings may be represented by different data types (e.g. float, integer). How is this best handled...
I'm using nrf52832 and building projects on it with the help of sdk 14 and sdk 11 for BLE. Now when I load my code for example the BLE HRS it loads properly with no error...
Hello,
I've upgraded my machine to Windows 10. I can't get Master control panel to work. I keep getting the error message:
No response from master emulator
...
