Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
Hi,
I need solution for modbus interface.
My One Central connected with Modbus Server App and 8 slave connected with each peripheral.
which SDK and Mode used for this...
Hi,
I just read Understanding NRF_ERROR_BUSY and wanted to know if this is true for the S132 V5 softdevice.
So each connection can queue one system Tx packet and one...
Hi everyone !
We migrated a functional code from IAR to GCC compiler. But we got some trouble working it with GCC. The code compiles but it doesn't act properly with GCC...
I have used Arduino for some time and i am very new to NRF. So i am struggling with any thing i do. But i am really motivated to learn it.
Completed setup for eclipse to...
Hi, I am designing a PCB which consists of an analog circuitry (microphone + analog front end) and the nrf52832 chip. I am using inbuilt-ADC of this chip to sample the acoustic...
I use this demo [nRF51_SDK_10.0.0_HID_DFU_090216.rar] (/attachment/27e0b68cff3ffe4959299fcae336e844)
change rep_map_data[] add mouse and Consumer,but restart is no work ...
Hi,
(I'm a computer scientist, please be kind)
In the below attached image, I have collected the data outdoors (so no signal reflection or signal fading) from a single...
Hello all,
I am using nRF51822 BLE SDK 9.00 PCA10028. I want to configure the gpio pins as input to sense the voltage as high or low. how to configure it please suggest...
hi
i'm developing to nrf52832, sdk14.0 version.
for example, ble_app_uart project..
NRF_LOG_INFO("UART Start!");
printf("UART Start!");
-> In serial program,...
I have an application that do SW download to STM32L151 processor using NordicDongle with MasterEmulator.dll (Version 2.1.13.14)
It works good on my desktop windows 10 computer...
Hello,
we are trying to test the mesh functionality with nrf development kit. We erased the flash on the dev kit and we programmed it with softdevice version s132v3.0.0....
As stated in the topic. We use BLE to simulate UART. As for now, we have defined our own UUIDs but there would be more straight forward to use the well defined and used one...
Hi,
I have known your board support jlink ob；I want to debug through it ;
I want to know if i need to buy the software-license from SEGGER ？
and if i need buy the software...
