Hello,
I'd like to ask what needs to be configured to enable communication between two boards: nrF7002-DK and nRF5340-DK via another UART (e.g. UART1).
Please provide...
Hi Team,
We are developing on a custom board with an nRF54L15 (Raytac Module with NRF54L15_xxAA_ENGB) and are unable to provision a pre-generated secp256r1 private key into...
Hi, I want to run Bluetooth Mesh Light example on nrf54h20 chip.
At the beginning I prepared devboard with this tutorial: https://docs.nordicsemi.com/bundle/ncs-latest/page...
Hello,
I am trying to build a firmware for the nRF5340 on the Thingy91:x. The firmware should use the external flash for the secondary Image and is using the chained bootload...
Hello,
I'm looking for answers and some explanation for two main questions - is it possible to perform non-simultaneous multi-image FOTA over WiFi? Is it possible to support...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
We are developing HW that includes nRF9151 running DECT NR+ with the Wirepas stack for mesh connectivity between multiple units. The product is expected to move between geographies...
When I try to copy hex files onto my board, the board un-mounts and remounts with a file called "fail.txt". The files says "OUT OF MEMORY".
I have tried hard resetting the...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Is it possible to configure the radio in such a way as to always capture the entire packet, this means everything after the preamble including the CRC? Of course this means...
I am using SDK9.0,
J-Link Lite-Cortex-M, HW: V8.00, DLL: V4.98C
But getting this error just in this project when debugging:
debug.txt
It was working with this project...
Looking at the ADC HAL, I see 8 choices for ADC input, plus a disabled case. Is it possible to choose as the input to the ADC a node that is proportional to the VCC battery...
We're building a low cost device with an nRF8001 as the only means of communication as physical access is closed after the device is built.
Is there any way to change the...
Hi Guys,
I would like to set up my nrf51822 to make a connection once a GPIO button is pressed and send some data. I've been using this sheet to try and calculate what...
Hello,
I've purchased 2xnRF905-EVBOARD
I made some test with a spectrum analyzer. The output of the module is nearly 10dBm as mentioned in the datasheet.
I connect the...
I'm using PCA10028,SDK9.0,S130.I want to set and get the ble address,but I found that couldn't get the ble address by using API sd_ble_gap_address_get,the chip will reset...
Hi, there! Does peripheral with ANCS only be connected by iOS? I ran the ANCS demo in sdk 9.0, and it works well with iOS. Once an Android phone connect to it, it was connected...
On developer site I saw "The RSSI value of the beacon measured at 1 meter distance, which can be used for estimating the distance from the beacon." I don't get it can any...
I am using HID service over GATT and have several reports defined. When I increase my report map data size by adding more reports, my map size is 280 bytes, whihc seems to...
I want to try the nRF Sniffer app but that requires that I reprogram my nRF51 dongle. I want to know that I can restore it before I do this. I can't save the current "as-shipped...
Hello,
We recently received an eval kit the the nRF52832, but we were told not to take current measurements with this version. This presents a problem since we are evaluating...
Hi all,
I'm using two nRF51 DK to measure ADC input on peripheral side and translate it to central, based on Multilink example.
One software timer is used to perform one...
