Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi there.
I recently migrated from SDK 13 to SDK 14.0.0 and followed the migration guide in detail. I've found that when I try to advertise, ble_advertising_start() will...
According to the nRF52810 datasheet,the reference circuitry with DC/DC regulator setup connet the pin DCC and the pin DEC4. Then how much is the voltage output of the pin...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hi
I am trying BLE multirole application ble_app_multirole_lesc from the SDK 13.0.0.
I am using nRf52832 DK along with GCC toolchain.
For debugging I am using Segger...
In the mesh network, the sender uses trickle algorithm to control the repeat sending process, and at last the sender will send the message forever in a max interval at a handle...
Hi Nordic Team!
After developing our firmware on the nRF52 HDK, we designed our custom board, and we're starting to write our custom board configuration file.
The main...
Hi,
we've developed a custom board with nrf51 and use bonding and white listing.
Everything works fine when connecting and bonding iOS phones with this devices but with...
HEllo,
I was wondering whether or not is advisable to use the same handler to handle transmission/reception of data over SPI0 and SPI1 interfaces.
I have two sensors...
Hello
I am using a custom board, based on nRF52832 CIAAB0. I have also S132 installed, and I am using SDK 13.1.0. TWI pins are P0.16 - SCL & P0.18 - SDA. The code is based...
I am trying to advertise some data using the s130 softdevice to my MS49SF2 (nrf51822 based module ) and then flashed the hrs example code to it..
Still I couldn't find...
hi, Nordic
I'm using your nRF51-DK(PCA10028) board, on android, i disconnect connection by call BluetoothGatt.disconnect ( developer.android.com/.../BluetoothGatt.html ,...
Hallo i am beginner developer, i plan to send sensor data to smartphone, i am still confused whether to use ble_app_uart or advertising mode, for example my case saw TrackR...
Currently I am using the spis driver to send data through the SPI peripheral. On the event handler I want to capture the time in which the chip is selected, which in the case...
I just opened my nRF52 DK and tried to flash the board. I got the error
ERROR: There is no debugger connected to the PC
Most concerning is that the LD5 light does not...
I have two nrf51-DK's (say A and B).
A , nrfStudio doesn't detects it.
(Windows doesn't even shows USB port connection in device manager, so cannot try nrfjprog -...
