Hi all,
we are wondering if there is a clean and reliable way to perform DFU on 54L15 via Thread? Our scenario: once the products get shipped to customers, the border router...
Hello,
We upgraded our project to nrf connect sdk v3.0.2 from v2.9.0 and can no longer use pin 0.00 and pin 0.01 as gpio. The problem seems to be in the nrf53 soc.c file...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Post:
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
I use the security mechanism dtls based on udp communication. Can I implement it on nrf52833? How much flash and ram should be occupied at least? Is there a suggested value...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
In nRF51 PS, I read typical/max time for AES ECB are respectively 8.5 and 17µs.
What would be those values for the whole AES-CCM operation (ie including MIC computation)...
Hello,
I'm working on a software we've made starting from the "ble_app_uart_s132_pca10040.uvprojx" source code. My "main" (procedure fct) is in the for (;;) of the void...
Hi,
A couple new fixes in listed files to supress gcc errors when -flto enabled.
hardfault_handler_gcc.c
port.c
Patches are in answer below.
Regards,...
I´ve read that the command "lib_aci_close_remote_pipe" is not available on the chip NRF8001 build code C. I need execute this command to solve a bug in the ANCS service. If...
Hi
I have setup and configured Eclipse using the tutorial and all seems to be good, except, I cant flash the binary to the chip. Here is my error when calling flash:
...
Hi folks,
I'm trying to write a program to check out a pair of nRF24L01p modules talking to each other, and I'm a bit confused about two aspects of initialisation:
...
We are using your nRF24l01+ chip in one of our products. we are using 1 nRF as receiver and 5 nRF's as transmitters.
While trying to use the chip with multiciever configuration...
Using SDK13 - I would like to use the fds/fstorage libraries, but I'm told that "The experimental label is due to lacking test coverage for the two modules". here
At the...
Hi,
I've been suffering with detection of writing to cccd to enable notifications. The S132 (nRF5_SDK_13.0.0_04a0bfd + s132_nrf52_4.0.2_softdevice) never fires BLE_GATTS_EVT_WRITE...
Hello, I'm migrating a project from nrf51 to nrf52, and there is this function:
uint32_t dfu_init(void)
{
m_cmd_handler = *((bl_if_cmd_handler_t*) (0x20000000 + ((uint32_t...
Hi,I use demo project in
nRF5_SDK_12.1.0_0d23e2a\examples\peripheral\saadc\pca10040\blank\arm5_no_packs\saadc_pca10040.uvprojx.
I made the following changes:
1.add...
Hi all,
what is the most correct way to delete the bonding information when the client and peripheral are connect.
Delete_peers
Wait the QUEUE_EVENT_PEER_DELETE_SUCCESSED...
Hi,
I have an nRF52832 sending data to a central device. At the central side I am testing two tablets (separately). One is a Samsung Galaxy Tab A 2016 10" and another one...
FDS error in FDS_VIRTUAL_PAGE_SIZE 1024 ?? (NRF51)
github.com/.../nRF52-fds-example
If I use FDS_VIRTUAL_PAGES 3 , FDS_VIRTUAL_PAGE_SIZE 1024 , then there comes FDS_ERR_BUSY...
