Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello,
For the softdevice update, is it the responsibility of the bootloader to make sure, that the softdevice was copied correctly?
If for example the bootloader calls...
Hi,
When i use FreeRTOS tasks with priorities 2,3,4,5 what i need to #define for XXX_CONFIG_IRQ_PRIORITY of SPI,SAADC and GPIOTE at the file sdk_config.h
Thanks
Hello, I use nrf51822 , sdk 8.0.0, s110
I defined advertise interval and timeout
#define APP_ADV_INTERVAL 320
#define APP_ADV_TIMEOUT_IN_SECONDS 3
Also, I write...
Hey Nordic Devzone,
I am really new to Nordic and am still a student in embedded software engineering. So first some background information.
I have 6x nRF52840 and 5x...
Hello,
I am designing a custom 2layered PCB board with NRF52832 IC. I have followed the reference design given in IC's datasheet as shown in the figure. Please provide the...
Hi,
I'm currently building a BLE multi-sensors device, with mbed online IDE. I succeed in implementing BLE API, and releasing a first .hex firmware with multiple services...
Hello,
I added an extra opcode to the DFU Control Point characteristic so that I can jump to the main application by writing to it. The problem is that whenever I do that...
Hi there,
quite a beginner here and tring to figure some stuff out about the nordic programming style.
when sniffing around the given examples in the newest SDK(SES...
HI,
I got 2 nRF52840 dev kits and I'm interested in testing the long range layer (LE coded PHY ) between the 2 modules, also scan for the second module RSSI value.
I...
Hello,
This is my first time working on BLE and Nordic, so this might sound strange.
I am trying to update data on the fly when the central requests char data.
I have...
Hello,
I am designing a 2 layer board with NRF52832 IC. I am following all design considerations and reference design mentioned in IC's datasheet provided by Nordic. I have...
Hello,
I am designing a PCB with NRf52832 IC. I have a query regarding the width of the feed line. In reference design files, the width of the feed line is 30mil. I have...
Hello,
I want to receive the More data ( >20 bytes ) in nrf51822 Board from the nRF ToolBox UART module.
is this possible?
What will be changed to be done in peripheral...
Hi,
I have designed a custom PCB using NRF52832 IC.I have followed Sparkfun NRF52832 breakout board for placement of NRF52832 IC core part(including antenna) which is similar...
