Hello, I’m trying to compile code for a u-blox C209 AOA Tag. I installed the nRF Connect Extension Pack and was able to build normally.
After adding some unrelated paths...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
Hi there,
I am trying to interface at25xe321d with QSPI but it always end up returning zeros. Please find attached code and dts file for reference. Thanks Moh
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
hi guys. i'm have a project with nrf52832.
i use jlink v8 debuger clone form china, just 12$ and have this troulbe in this figure
Untitled.png
could you help me?. jlink...
Hi,
I was trying to write the s132 SoftDevice from the nRF5_SDK_13.0.0 onto the Sparkfun nRF52832 breakout via OpenOCD and an ST-Link v2 debugger. The SoftDevice flashed...
Greetings -
I am working on a peripheral-heavy project. Many of the devices seem to work Just Fine with VDDio of 1.8 volts. On device seems to be having fits and I need...
void Gzll_TxSuccessCallback(uint32_t pipe)
void Gzll_TxFailedCallback(uint32_t pipe)
More than two functions are not accurate judgment
GZLL agreement return function cannot...
I try to implement this library to my code.
uint32_t settings_set_erase_flag(int32_t flag)
{
uint32_t err_code = fds_write(flag, ERASE_BOND_FLAG);
return err_code;...
Hello I have this error:
Checking installed packages
pyside: 1.2.4
pyqtgraph: 0.10.0
numpy: 1.12.1
pynrfjprog: 9.0.0
Warning: The software is tested with PyQtGraph...
I wrote a peripheral similar to NUS. Then I use the multilink central to connect to 3 of them. First two are fine. But when the 3rd is added, the 3rd one would connect, but...
Hi,
I want to make an BLE_UART dongle which will receive the data from the module(An external module is connected through UART) and it will be send over the BLE to ble_receiver...
I'd like to write some timestamps to a log variable in order to see how much time has elapsed between certain points in my code. app_timer.h has two functions that look suitable...
Hello,
I have a problem while combining peripheral examples in SDK13. I am trying to combine twi_sensor and uart but when I do this in uart folder, compiler gives following...
Hi support team,
We met an issue for connecting our device built in nRF51822 to Android device.
The nRF51822 uses below firmware program:
nRF5_SDK_12.3.0_d7731ad...
Hello,
I am working UART_BLE_APP , my query is when we transfer the data form smartphone application to the device where the data will get stored in device and can we access...
I have created a characteristic for sending up to 60 data bytes in a buffer using a sequence of 20 byte notifications sent to an external device. This works quite well for...
Hi,
What is an optimal transmission power to maximize the coded PHY range, but still stay within ETSI regulations? Can nRF52840 actually exceed the regulations if I set...
Controller:
nRF52832-QFAA
Reference project:
nRF5_SDK_11.0.0_89a8197/examples/dfu/bootloader/pca10040/dual_bank_ble_s132
Question:
The idea is, to store a init_DFU_by_flag...
