Hello, I am developing my custom board using Thingy53 as a reference design. I am trying to achieve DFU from application using external flash for the secondary image and upload...
Hi, we are developping a medical device that receives an audio stream from a smartphone. We have a custom board connected to a different DSP than the one in the nrf5340_audio_DK...
Hi! We're testing nRF7002 with the nRF7002-DK and NCS v3.0.2. CONFIG_NET_ZPERF=y has been added to the nrf/samples/wifi/shell/prj.conf, the rest is untouched. Running that...
I am using the nrf5340 on a nrf7002fk dev kit. I am interested in low power operation so I am measuring the power consumed.
I am running a simple app:
int main(void) ...
Hi,
I have a simple question about Bluetooth Channel Sounding:
Question: If I use BT_CONN_LE_CS_MAIN_MODE_3 as main mode (PBR + RTT), does it make sense to use sub mode...
Hello Nordic Team,
I am currently working with the NRF54L15-DK. I have successfully configured the simple ADC on AIN4 (P1.11) and am able to read the raw sensor values....
i am writing data from wav file to w25q128jv and i got error -22 at some offset while writing. i tried many config but it seems the problem is not solved, does anyone have...
hi
here i have use block size 16 byte and block count 5096. this is my start address 0x27000
i have tried to clear 79 pages.
and read data from flash with specific...
Hello to all
I have the next code, basically what it does is reading a button state and if it is pressed then the manufacturer data of the BLE package is lets say B, on...
Hi All,
I would like to know what the default value is for the radio TX power for the nRF5240. According to Nordic's specification, the output power is programmable from...
In the ULP Wireless Q magazine (edition winter 2016), on page 12 / 13 there is listed that the nRF52 chips have a Battery Monitor peripheral but I cannot find anything about...
I have been developing my application using gcc on an NRF52 by putting the text section at 0. This was convenient to get going quickly. We initially weren't going to launch...
hello, i am doing flash read and write in nrf51.for which i have used the C:\nRF5_SDK_12.2.0_f012efa\examples\peripheral\flashwrite\pca10028\blank\arm4 this exampl.
but while...
Hi,
Could somebody share the schematic and board files of nrf51 beacon?
We are planning to make some changes. I don't intend to buy a beacon because I have already purchased...
Hi,
I use the bootloader in the SDK V13.0, I found that no timeout as the SDK v12.x. However, I have added the WDT to the bootloader refer to the link link text
it still...
i could not run timer2 with soft device,. if i start initiaize TIMER2 the bluetooth advertise has disabled. i need this timer to timeout my flow function. i think softdevice...
Hi,
I used the hrs example found some problems, the problem is described as follows:
I use the Android phone pairing binding device, when I cancel the pairing on the phone...
hello,
What is the difference between the next two events?
On_ble_evt ()
BLE_GAP_EVT_TIMEOUT == 0x1 B
On_adv_evt ()
BLE_ADV_EVT_IDLE
I can not understand well.
With...
Hi;
I do not know the BLE Event(DFU bootLoader/SDK Sample) so I will ask you a question.
The environment using is below.
SDK v10.0.0 (Sample code/dfu_transport_ble...
I was trying to save this :
char a = 'r';
uint8_t save = a ;
record_chunk.p_data = &save;
Or even this :
char *point ;
char word[5]="lala";
point =word...
