Hi there,
I am trying to interface at25xe321d with QSPI but it always end up returning zeros. Please find attached code and dts file for reference. Thanks Moh
Hi,
We have a custom PCB based on the nRF9151 and nRF7002 for a tracking use case, supporting both indoor (Wi-Fi scanning) and outdoor (GPS) positioning. Our firmware is...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
The nRF54L series is a new device to the nRF family, and during the bring-up of the chip from early engineering samples to mass production devices there have been quite a...
Hi,
Kindly help with some insights/tip on how to debug this hardfault. The code gives hardfault on my custom board, but not on NRF52-DK. My custom device is only populated...
Hi,
I am currently in the process of interfacing the HMC5883L magnetometer with my nrf52 development board. I have verified the connection to be working using a logic analyzer...
I have one central(SDK 10.0 S130) and one peripheral(SDK 8.0 S110) device. Normally central device can connect peripheral device it's ok but the peripheral device will stay...
Hi Nordic,
I'm porting hrs application on nuttx OS. But when I call sd_softdevice_enable function, it goes to "RESET". I read below article which mentions that SVC handler...
Hello all.
I'm having some problems with compiling the bootloader_secure project:
I downloaded SDK zip from http://www.nordicsemi.com/eng/Products/Nordic-Thingy-52 and...
Hi, I would like to detect the presence of a particular device in an environment where there are many devices advertising. The advertising packets are received by a scanner...
I want to send the continuous data over the BLE which is received by the UART of my nRF52 Evaluation kit. The BLE connection is getting disconnected while sending bulk of...
Hello Everyone,
I am new to BLE world.
Currently using MDBT40 which has nrf51822 as core: www.raytac.com/.../MDBT40-ANT-D.pdf
I am following this repo: github.com/...
I want to use nRF51822 Bluefruit LE Friend device (blue board) as BLE Sniffer. My OS is Windows 7 64-bits.
I installed ble-sniffer_win_1.0.1, v1.0: FTDI Driver Requirements...
According to another question here:
devzone.nordicsemi.com/.../
I'm stuck with waiting for the LFCLK to boot forever.
Normally, keil has a .s startup file that dictates...
Hi,I use the SDK 12.2.0, I want to add the peripheral RTC example to the ble_app_uart.I find the softdevice have used the RTC1 ,so I want to use the RTC0,but when I added...
Hello,
I am seeing something strange wrt to reassigning the NFC pins (9,10) on my Rigado BMD-300-EVAL using nRF SDK12.1 and gcc to build. I have two SPI based sensors on...
test_ble_mouse_wo_bootloader.pcapng Nordic_Mouse.pcapng connect_to_phone.pcapng test_ble_mouse_1.pcapng test_ble_mouse.pcapng Hoping someone here can help. The setup is a...
My problem seems to be related to this unsolved question.
I've making a central application to connect to my peripheral but I'm having a hard time getting the service discovery...
Hi friends..!
I am trying to print data on UART but only just after when TIMEOUT (180 sec) occurs in the project BLE.zip .
Is there something BLE stack event has to be used...
