Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I am developing an application which involves control of a brushed DC motor with a quadrature encoder. According to this post, in SDK 12.2.0 - which I am using - it is possible...
Hi,
I had a problem with my NRF52 chips. I'm using one BL652 (Laird) with SoftDevice s132 (4.0.2) and a standalone nRF52832 also with the same SoftDevice. I was trying...
hi guys. i'm have a project with nrf52832.
i use jlink v8 debuger clone form china, just 12$ and have this troulbe in this figure
Untitled.png
could you help me?. jlink...
Hi,
I was trying to write the s132 SoftDevice from the nRF5_SDK_13.0.0 onto the Sparkfun nRF52832 breakout via OpenOCD and an ST-Link v2 debugger. The SoftDevice flashed...
Greetings -
I am working on a peripheral-heavy project. Many of the devices seem to work Just Fine with VDDio of 1.8 volts. On device seems to be having fits and I need...
void Gzll_TxSuccessCallback(uint32_t pipe)
void Gzll_TxFailedCallback(uint32_t pipe)
More than two functions are not accurate judgment
GZLL agreement return function cannot...
I try to implement this library to my code.
uint32_t settings_set_erase_flag(int32_t flag)
{
uint32_t err_code = fds_write(flag, ERASE_BOND_FLAG);
return err_code;...
Hello I have this error:
Checking installed packages
pyside: 1.2.4
pyqtgraph: 0.10.0
numpy: 1.12.1
pynrfjprog: 9.0.0
Warning: The software is tested with PyQtGraph...
I wrote a peripheral similar to NUS. Then I use the multilink central to connect to 3 of them. First two are fine. But when the 3rd is added, the 3rd one would connect, but...
Hi,
I want to make an BLE_UART dongle which will receive the data from the module(An external module is connected through UART) and it will be send over the BLE to ble_receiver...
I'd like to write some timestamps to a log variable in order to see how much time has elapsed between certain points in my code. app_timer.h has two functions that look suitable...
Hello,
I have a problem while combining peripheral examples in SDK13. I am trying to combine twi_sensor and uart but when I do this in uart folder, compiler gives following...
Hi support team,
We met an issue for connecting our device built in nRF51822 to Android device.
The nRF51822 uses below firmware program:
nRF5_SDK_12.3.0_d7731ad...
Hello,
I am working UART_BLE_APP , my query is when we transfer the data form smartphone application to the device where the data will get stored in device and can we access...
I have created a characteristic for sending up to 60 data bytes in a buffer using a sequence of 20 byte notifications sent to an external device. This works quite well for...
