Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
I would like to implement DFU with firmware encryption. I'm aware this isn't present in SDK 12 and would like to modify the secured bootloader to implement it.
As...
I'm seeing the sd_ble_evt_get return NRF_ERROR_DATA_SIZE even though the supplied buffer and length param are larger than the event length. Is this a known benign issue? ...
I need to upgrade my soft device from "s132_nrf52_2.0.1_softdevice" to "s132_nrf52_4.0.2_softdevice". As i am migrating from SDk11 to SDK13.
While migration i found out...
I'm trying to port my code using pc-ble-driver-1.0.0 to use the latest official version 2.0.0
I see library names changed (from pc-ble-driver-1.0.0.* to pc_ble_driver_shared_sd_api_v3...
Hi,
I got an err_code = 0x00000007 after calling this function.
void system_timer_start(void)
{
uint32_t err_code;
err_code = app_timer_start(m_one_ms_timer_id...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
Hi,
I set up a 2 GPIOTE interupts like this:
in main.c:
APP_GPIOTE_INIT(3);
err_code = app_gpiote_user_register(&mainUser, 0x00000000, (1 << RF_GPIO2), powerButtonInt...
Hi
I am using sd_ble_gattc_primary_services_discover(conn_handle,0x0001,NULL) to discover primary services on a GATT server. After the first call to this function, I get...
In nRF51 PS, I read typical/max time for AES ECB are respectively 8.5 and 17µs.
What would be those values for the whole AES-CCM operation (ie including MIC computation)...
Hello,
I'm working on a software we've made starting from the "ble_app_uart_s132_pca10040.uvprojx" source code. My "main" (procedure fct) is in the for (;;) of the void...
Hi,
A couple new fixes in listed files to supress gcc errors when -flto enabled.
hardfault_handler_gcc.c
port.c
Patches are in answer below.
Regards,...
I´ve read that the command "lib_aci_close_remote_pipe" is not available on the chip NRF8001 build code C. I need execute this command to solve a bug in the ANCS service. If...
Hi
I have setup and configured Eclipse using the tutorial and all seems to be good, except, I cant flash the binary to the chip. Here is my error when calling flash:
...
Hi folks,
I'm trying to write a program to check out a pair of nRF24L01p modules talking to each other, and I'm a bit confused about two aspects of initialisation:
...
