How to prevent storage partition from erase durning MCUBOOT firmware update?
I use Settings with NVS to store data
CONFIG_FLASH_MAP=y
CONFIG_FLASH=y
CONFIG_SETTINGS...
Hi,
I am building a Thread network ( www.youtube.com/watch with a Rasp Pi 4 as a border router, an nRF52840 DK as an RCP, and an nRF5340 DK as a child to be added into the...
We found a problem with a client's legacy design. They use two 12 pF load capacitors for the 32 MHz crystal, which has a 4 pF capacitance. This is a somewhat unusual Abracon...
Hello DevZone,
I have a project where I currently use the AT%XPOFWARN feature, in order to turn off the modem in case the battery voltage is too low. It's used in both cellular...
We use several Nordic chips in our BLE sensors. We bond to the devices from Android, connect to update configurations, then disconnect such that the device then advertises...
Dear Nordic DevZone,
I'm encountering pairing issues with mobile devices and a nRF54 DevKit flashed with HCI over UART firmware. After initial pairing, deleting the bonding...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
S110 8.0.0 was just released allowing a larger ATT table, which is something we need, but is there a corresponding SDK update for this SD before we spend the time upgrading...
I am a very beginner on embedded field.
I have a nrf51822 and tmp 102. I follow this direction on mbed site
link text
and it's actually working. The code provide...
Hi,
I have a similar problem as described in
devzone.nordicsemi.com/.../
I have eliminated my program to be:
int main(void) {
setupLEDPins();
BluetoothPeripheral...
We are having some trouble with battery percentage measurement. The battery percentage being reported, keeps fluctuating. Earlier the fluctuations were as large as 3% to 100...
Hi,
I recently made some changes to the code and noticed the following errors for the first time.
Error: L6406E: No space in execution regions with .ANY selector matching...
Hi, all!
I am rencently studying ota,and that is what I have done:
Program softdevice 6.0 into my nrf51822 chip.
Program bootloader(version in SDK5.2) into my nrf51822...
hello everyone,
I recently purchased the new nRF51 dongle. I could successfully load the blinky example with S110 soft device to it. But it is not working with the HRS example...
Hi, I am trying to use your new sd 8.0.0 but there are a lot of compilation errors due to the new APIs and removed section from security structs in SDK 7.2.0.
Are we to sole...
Hello
I have the nRF51822EK PCA10001 (V1.0) and PCA10000 (V1.0).
I'm working on a project where i'm going to send data from a custom board over to the PCA10000 dongle...
Hi all,
I have a small question. If a GATT server needs to send data to a GATT client(about 65 bytes), does it have to create a service first and then adds characteristic...
i am trying to make connections between s130 device and end node which have heart rate service.
according to the s130 document once if you press the button 0 it will automatically...
Hi
during setup of a peripheral at startup, I need to add some wait periods in between steps of the setup. Is there some function like waitMS(int time) or something, that...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Folks,
Newbie here with mbed, using nRF51-DK, but old hand with nRF51822, S110, SDK, J-Link, Keil MDK, etc. Trying to figure out how the mbed SDK API maps down onto the...
