I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
The absolute max throughput for the nRF52 using S132 v2 was 128 kbps .
The new S132 v3 was recently released and boasts throughput increases by 400%. Has anyone tested...
I am trying to send small data packets of up to 9 bytes at the fastest and most consistent rate from a nRF52 peripheral to a nRF52 Central. Both use the s332 SoftDevices....
Hello !
I've created an app based on the nrf blinky master : it works perfectly on my smartphones.
But when I kill the app, and when I relaunch it, it doesn't connect...
Hi,
I am trying to use a mux change among 3 differential channels. The diff signal then goes through an instrumentation amplifier. The steps I'm using:
switch to ch1...
Occasionally, when trying to program a softdevice in nrfgo studio, it can't find the softdevice hex file. It was there during the last several programming sessions, but now...
I would like to achieve in the room inside a number of devices to achieve one-to-one binding 8K / S unidirectional transmission of data, is not the use of proprietary_rf inside...
Hi,
I have set up a two NRF51DKs one in a central and one in a peripheral role. Using MCP and nRFConnect I have confirmed that I can send read requests to my peripheral...
Hi,
the documentation page of Gazell warns that it is outdated.
Warning: This is old documentation, and should only be used for historic reference. Please go here...
Hello,
can you help me with choosing the right software components for nRF51 and nRF52 ?
nRF51 on the left hand side works on the battery and turns on when the button...
hi,
I am working on nrf52 sdk11 and s132,
when I am using ble_app_uart example on my custom board I used nrf_delay_ms(10000) i.e 10 seconds when i observe current consumption...
When i use sd_ble_gatts_hvx() send package,i can use the usb dongle get the data package,as it show i can get the information such as, LLID, MESN, SN,MD,PDU-Length show in...
Hello,
I am trying to scan a local name for beacon device on nrf51822 SDK12.0.0 ble_app_multilink_central. The original peripheral sample was working as well. But the beacon...
I am using SDK 12.0.0 and Nrf51 ship.I was trying to compile micro-ecc library in eclipse using make file.I have cloned the micro ecc library from this link .I am using the...
Hi,
I want to eraze the flash page of nrf52832.
Since the default flash page size is 4096 bytes, it takes 90ms to eraze the page.
I want to shorten the time for erazing...
Hi!
I have to do an application is talk via bluetooth. I think i use codec IC to sample the voice then send data via bluetooth. In the receiver device , I use other codec...