We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hello Folks,
I am currently try to program RedBear BLE nano board (which is essentially nrf51822) using Nordic SDK v12, which has features of secure OTA. However after...
I have started working on the external file access with NRF
is it possible to read or access the data from the external file into NRF programming
similar to what we do...
I am running a modified version of the app_uart_c example on a nRF52832 using softdevice 132.
I want to send a large hex number to the peripheral I'm connected to. Is it...
Hi,
No matter what I adjust, I can't get the PPK to output over 2.2V. I happen to be using an older nRF52 preview DK (figured it'd be a good use for that board now that it...
tl;dr: UART transmission sometimes stops and never resumes. Only a
power cycle resolves the issue; a system reset is not sufficient. The
problem only occurs when flow control...
Hello,
as far as I have gathered, it is possible to use multiple peripherals on one device with the current alpha release of the S132 Softdevice. What I did not understand...
Hello,
today I had a problem where a timer was causing my device to reset after a while, because the app scheduler queue got full and it was raising an NRF_ERROR_NO_MEM...
Hi!
I am playing with NRF cloud and Android phone gateway. I am not able to find out how to carry out firmware update over NRF cloud. Would you please shed some light?...
I am developing an application with a single service that has a single characteristic with read and write operations.
I want to give the ability to writing to this characteristic...
Hello,
I am working on a project with STM32 master and nRF51822 slave connecting to Android/iOS mobile apps.
I send the advertising parameters from STM32 to my nRF51822...
Hi,
I am new to firmware engineering. I have a simple and basic question.
If there's Timer A and B, and both interval is 100ms, what happens to the timeout handler functions...
I want to add some configuration files to nrf52, so can I write data in flash and read when I want.......I have the example code of twi master_twi slave but it engages the...
I have followed the instructions for sniffing ble packets with wireshark. Errors would occur when using 2.2.5 so I switched to the latest development version. See this question...
Hi, I am developer of indoor location tracking solutions for asset tracking applications, actively looking out for new technologies, i would like to understand what are the...
Normally I am using nrf51 for peripheral(sdk 8.0.0 s110) and central(sdk10.0.0 s130) device. But I want to use nrf52 for just central device. I tried nrf52 for central(with...
