Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
Hi,
I use it as a translator for Google, so it may be strange in context. please understand.
I was in big trouble.
I used the nRF51822, S110, and SDK9 in my previous...
Hi. We are attempting to use the Infineon XMC1202 LED shield with our NRF52 device. The XMC1202 has an I2C address of 0x15E, instead of the traditional 7 bit address. We have...
I've tried linking the ESB library (esb_arm.lib) in Eclipse by adding it to my nRF51822 project's Makefile, but I am still getting undefined reference errors during build...
Hi
We are going to use the Taiyo Yuden Evaluation Board - EBSHJNZWZ.
As i understand, the board firmware used the Nortic SoftDevice S132
The question is :
May i...
Hello,
I'm trying to compile an example of nRF52_SDK_1 but I get this error:
make
Makefile:150: Cannot find include folder: ../../../config/receiver_pca10040
Makefile...
Hello,
I've been reading over different examples and questions on the Nordic Developer Zone but still have some questions about multiple SAADC channels.
1 - If I initialized...
I've been developing an application on the nrf51 DK based on the ble uart application and it's been working fine. I've ported it to a custom board running at 1.8V and attached...
Greetings -
I am using (the slightly out-dated) 12.3 SDK with a nRF52840. I'm also using s132 as my softdevice.
As I've been slowly reducing my RTC interrupt frequency...
Hi,
I want to activate readback protection on nRF51822, in a simple project without bootloader without softdevice.
My compiler is GCC and the const uint32_t UICR_RBPCONF...
Hi. I don't understand how to build nrf_drv_saadc.c with gcc. I'm getting this error in the EVT_TO_STR() macro:
Compiling file: nrf_drv_saadc.c
In file included from ...
Hello,
I'm going to use nrf52-ble-image-transfer-demo-master for my application.
But demo used other way with cpp code for configuring nrf52832 interfaces(spi, twi, gpio...
Hello Folks,
Nice to see an active developer community out here! I ran into some issues last night which I hope could be resolved. We procured nRF52840 SoCs and have developed...
Hi all,
i'm new to BLE in general, I found this chip (nrf52832), which suits my uni project.
However, I don't have much knowledge about this technology. therefore, im...
Hi everyone,
I would like to test the capabilities of nRF52840. I understand that it should be capable of higher throughput (x2), increased broadcast capacity (x8), and...
