Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
When an NUS Central has several NUS Peripherals connected, is it possible to send the same "message" to all of the connected peripherals at once?
Or do I just have to iterate...
Hi,
It looks like we're experiencing an issue with uart's and digital inputs on an "S132 SoftDevice". Both an UART and digital inputs are used. The UART is initialized using...
Dear Sir/Madam,
I am playing with SDK12.2 on PCA10028 board and runs its HRS example. This example has a battery service and its battery level characteristic could update...
I use DFU. All ok. But I need to store my settings after update. As I was advised, I located my data from address 0x72400
But Keil added after this struc some code
...
Please Find the Attachment Screen shot of SDK Document for Advertising Module. Also Side by Side I am doing Code Walkthrough Blinky Peripheral . The Code in Blinky No Where...
Hi,
In function advertising_init(void) , I have set
and in function gap_params_init(void), I have set
still the icon doesn't change. What could be the possible reason...
Hello,
I'm trying to program my custom board with a PCA10056 following this scheme (Note that my custom board is powered by the PCA10056) :
VDD (PCA10056) ---> VTG(PCA10056...
Hi,
I'm using nRf52840 rev B and C chipset and not able to detect the NFC on the device (the rev A chipset is working). Following SW combination is used:
nRF5_SDK_15.0...
Hello,
I am working on Multi-link. I want to scan the advertising information and connect only the uuid I set up.
I want to process it on_adv_report (), but I do not know...
The output order of my scanning Saadc is not predictable.
I found two related questions, but they both are for SDK 11 and seem to have been resolved.
devzone.nordicsemi...
Hi,
Am I right that after provisioner done with network configuration all nodes save their info in persistant storage and continue work without a provisioner?
How provisioner...
HI
i'm trying to use TSL2561 sensor, but i can't geting to work. I found the code that works on the psoc that, I change it so it fits nrf52840 but it still does not work...
I want to be sure about erasing flash. Flash is divided into pages and each page has 8 blocks. The smallest amount of flash you can erase is a PAGE. Is this correct. In other...
hello,
I'm currently stuck with sd_app_evt_wait() function leaving for an unknown reason. This function is called in the main loop.
The only reasons that shall exit the...
