Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi Guys,
I'm doing the RF test based on nRF24le1, could you share any good antenna sample for this chip?
i found a TI 2.4g antenna design http://www.ti.com/lit/an/swra117d...
SEGGER EMBEDDED __align(4) have error info.I can use __align(4) normally, but there is a error information in SEGGER embedded
this error is "expected declaration specifiers...
Hi Nordic Devzone,
I'm working with nrf52-PDK and Mesh SDK, I wanted to know that if it is possible to send and receive some data at the same time?
And if I can do that...
I have made a custom board by following the reference design given in the nordic website using 2450BM14E0003 Balun and 2450AT18B100E chip antenna from Johannson technology...
HI,
My application is based on on your example ble_perepherical/ble_app_uart.
I realised few modification.
Now, after a BLE timeout, the circuit doesn't sleep anymore...
I am requesting timeslots with an interval of multiple seconds. But sometimes I want to switch to an interval of several milliseconds. How can I cancel the pending timeslot...
Using some of our nRF51 dongles as sniffers to debug BLE.
Sniffer software --> "w" --> Wireshark, no problems.
Post processing wireshark export *.csv files. No problems...
Hi.
Is there some code example for Bluetooth button for PTT aplication Zello ?
When I press a button BLE should send notify event =1, when released BLE send notify event...
I'm building battery power BLE mesh network the nodes mast have the publishing period match greater than 5 minutes. And my question is how to estimate the power consumption...
Hi, I have a spis problem when nrf_drv_spis_buffers_set is called, it enters the switch on the SPIS_BUFFER_RESOURCE_CONFIGURED case, then calls spis_state_change with SPIS_BUFFER_RESOURCE_REQUESTED...
Hello,
I'm using the examples light_switch_server_nrf52832 and light_switch_client_nrf52832 to send data over Bluetooth Mesh. Using the description from creating new models...
In the SDK the multi protocol example switches back and forth between Gazell and BT with a button press. Is it possible to maintain a BT connection and a Gazell connection...
Hi,
I have a quick question regarding isochronous data transfer. This type of transfer is still in the draft but are there any hooks in SoftDevice that would enable us to...
Hi I'm brand new to use nrf52840, but hope there is one that can help i need a counter / timestamp. If it's a counter, it still has to count even if you do something else...
Hello Everyone,
I am using Martinsbl / nrf5-mpu-examples nrf52-mpu-easydma-using-timers-and-drivers. When I tried to change the TWIM_RX_BUF_WIDTH to get the gyro data, the...
