Hello Nordic Team,
I am currently working with the nRF54L15 DK and interfacing an occupancy sensor over UART. In my standalone application (non-Matter), the UART communication...
Hi,
I'm getting the following error over and over again from the nrf connect plugin in VSCode:
[west]: FATAL ERROR: failed manifest import in bsim (tools/bsim): [west...
this my yaml.file to use partition manager, beacause iam implementing DFU, USB MSC with fatfs in single project
fatfs_storage :
address : 0x00000000
size : 0x00200000...
i am working on custom board nRF52840 with display ST7789 + touch Ft6336
1) i want to use LVGL library with Display how do i get started with LVGL .Any tutorials or sample...
Hi,
I want to use nPM1300EK、nPM PowerUP (official v2.1.1) profiling a chargeable battery, whose rated capacity、standard charging current is 2000mAh and 400mA respectively...
Hello,
I'm developing my custom sensor application. It's a matter over thread device. Before final product I'm working on a NRF52840 DK PCA 100056 v3.0.1 and NCS 3.02. It...
Hello,
I higly need to run twister unit tests in debug mode with breakpoints, step by step, spies and other debug tools in vscode. I did not find a way to do so.
Is...
I am currently working on a device using a nRF905. We want to use the device in Region 2 (USA).
This means that we need to use frequency hopping between 902 and 928 Mhz....
Hi,
I'm implementing a simple bootloader which will not use BLE.
Application will transfer the data from mobile devices using BLE and this data will be stored to...
I'm looking for a smart solution to connect my application to different ANT+ sensors and transmit a logfile to a mobilephone via BT (and receive notifications from mobile...
Hi~ Sir:
I test S120 connect with S110 have problem ,test methods are as follows
S120 connect with S110 ,function ok.
S110 Power Off and On, the interval time about...
Hello everybody,
I've been digging through the forum and the documentation for hours now. But to be honest I don't understand the whole timer thing.
I need a simple...
Hello,
while implementing a BLE link layer, I’ve stumbled over a race condition, where I have a problem to find the cause. Maybe someone of you have an idea, on how to...
I am reading data over the duration of 3 seconds on SPI, but while I'm doing that, I need to send that data over RF using microESB library.
I need to make sure the read...
I use the chip nrf51822, However, SDK8.1.0 example ble_app_uart is base on nrf51422, what I need to do? just replace bsp.c ? and which bsp.c file corresponds to the nrf51822...
I'm tring to build a FOTA broadcaster machine using a raspberry-pi with bluez. or any other Linux small linux embedded system.
The idea is that after testing the board...
I cannot program an external nRF51822 module(program old softdevice S110 6.0.0) with nRF51-DK p20 (SWD), it give message "invalid parameter error".
and i program the 51422DK...
Hi all,
I want accive this situation. My peripheral connecting a central with a service for example hrs, then i stop the conect with the function sd_ble_gap_disconnect(m_conn_handle_peripheral...
Hi,
I am using the sample BLE_gls code provided by Nordic.
I have made the following changes in the code:
#define SEC_PARAM_MITM 0
#define SEC_PARAM_IO_CAPABILITIES...
I am using nrf51822 qfaa IC (pca10004 board) with softdevice v8 and sdk9. Now I am trying to do the dfu example. I uploaded the softdevice with the help of nrf gostudio. But...
Hi,
Please correct me if I'm wrong.
Consider an application that will read 6 bytes of data from I2C at 200Hz (each 5mSec) and will stop after 2000 reads. This will be...
Hi,
Apologies if this is an obvious question, but I haven't been able to establish from previous questions or the data sheet whether it is necessary to use an external...
